Switches - Small Business - Page 404

Updated: Switches board in read-only mode June 18th - July 2nd

Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...

Helpful support links - Videos, Hardware Installation Guides

Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Installation Guide - Catalyst 1300Hardware Installation Guide - Catalyst 12...

How do I route multiple SB302 switches at different sites and their VLANs?

Hello Cisco Support Community, First thank you for any replies.The video posted today on 302's and multiple VLAN's on one switch was nice.Thank you, I have that working but it's not really what I need.Though pictures are worth a 1000 words so I hope ...

Resolved! Setting up VLAN across SRW2048 & SG300-20

Hi all,I have a Linksys SRW2048 which has workstations connected to it. This switch is connected to a CSB SG300-20 via fibre which has the servers connected to it. The problem I have is that where the internet comes into the building is near the Link...

Strange Error on Switch

Hi Guys,Last week and just yesterday, our switch SG200 50/50 logged an error like this:%CDP-E-MALFORMED_TLV: CDP message from 88:43:e1:ab:66:f8 cached with illegal Appliance VLAN-ID TLV At the time of the error, the SA520 router's LAN Port 1 where t...

Need Help to Configure - SG200-08 - VLAN issue

Any assistance would be very much appreciated.

'show interface trunk' output

My question is..interface Gi0/1 on access switch (Switch A) configured as trunk port allowing multiple vlans (say vlan 100-105)Now, this interface Gi0/1 on switch A has no issues and configured fine. Another switch B connected to Switch A and workin...

Resolved! SF300-48 - I want to have two VLANs talk to each other

I want to segment out our wireless users from our wired users and I purchased this switch in hopes of being able to do that.How do I go about doing that? I have already put the switch in layer 3 mode.I have created the second VLAN and assigned it an...

VLANS Between SGE2010s and SLM2024 via Fiber

Hi folks,I am new to the whole VLAN thing, so excuse my ignorance. I have successfully set up a VLAN on my primary switch which is an SGE2010. I have 3 other switches is other buildings connected in series. The next in line is another SGE2010 and...

SG200-18: Should I update firmware?

Usually with servers and all I'm gung ho about updating firmware as it fixes problems. But really never mucked too much with switch firmware. We just got a SG200-18 new from Dell as they sell Cisco stuff. It came with 1.0.0.19 firmware version. But I...

Resolved! ip igmp snooping querier?

i've been reading these forums and noticed that lot of people have problems with configuring multicast. basicly, problems are flooding bandwidth, no querier, confusing pim router configuration ...also, ive seen some promisses from tehnical stuff that...

End Of Life?

Hi,Is also the SR2024T-EU EOL?

Resolved! SPS224G4 pinouts

Does anyone have the pinouts for making a serail cable to connect from a pc to the LINKSYS SPS224G4 Switch? Thanks!

SF100 Won't Connect

I recently purchased a SF 100D 5 port switch, that is frustrating me. I currently have a New dell PC connected through a wall jack to an existing router, and wanted to add an ethernet printer. When I connect everything to the switch, I can only ge...

ESW 520 24-Port switch with POE not working???

We just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Can someone assist with tips for troubleshoot...

SF 200-24P - Rebooting Problem??

Hi AllI have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens1. Fa...

Static Routes Help

We recently purchased a SF 300-48P to replace a Layer 3 3Com switch that died. I've sucessfully put the switch into Layer 3 mode and assigned ip addresses to each of the VLANs but I cannot figure out how to implement routes for those. Here's some inf...

Switches - Small Business

Forum Posts