Switches - Small Business

I am a managed switch n00b.  Please forgive my lack of experience, but I think I have a relatively simple situation that I am just not totally clear on.System configuration:T1 from Cox => WAN Port of WRVS400N wireless RouterPort 1 of WRVS4400N to g1 ...

I am trying to find an unmanaged cisco switch that has cdp.  Technically the switch doesn't have to be unmanaged, but I am looking for a cheep switch with only 5-10 ports that also has cdp.  I can't be sure if the small cisco SD series switches, form...

I just received my brand new SLM2024 managed switch.  I connected my laptop to the switch via cable (turned off my wireless connection), opened up FireFox and entered 192.168.1.254 into the address bar.   No response.  I tried several ports on the SL...

Hi,I have got two smb pro switches and both of them are SMB PRO 520 switches. Can them be stacked or it has to be dot1q trunk to conenct them together?rgdsarman

Hi There!  This is my first post and I have no idea what I am doing when it comes to SNMP.  We are trying to evaluate our network performance, so we have downloaded a copy of Solarwind’s Orion and installed it on a server.  The topology is as follows...

I have a workstation on this switch that is running WireShark and I need to get packets to it.  However the moment I turn on port mirroring the station loses IP connectivity to the network.  I tried Rx only, Tx only and both and all three settings kn...

Hi,My Linksys SE2005 (v2.1) switch does not work with my Belkin N1 Vision router.If I cable a PC direct to the router it works. If I cable via the switch it does not work - the PC cannot configure the network settings (it can't even access the router...

I have a Linksys SGE2010P 48 Port switch with POE and I cannot get the firmware to upgrade.I have downloaded the firmware software from the site: http://www.cisco.com/en/US/products/ps9985/index.htmlEverytime I run the EasyUpgrade application I get t...

Hi there again,after upgrading our sge2000 from fw 1.0.0.45 via 3.0.0.17 to finally 3.0.0.18 we cannot upload the previously backup'd configuration files. first comes the msg "copy failed", then "copyjob completed with errors". but the configuration ...

Hello there,we have a server deploying images via pxe to several clients the same time and want to enable muticasting at our sge2000 switch. i tried to read the help/support manuals of the switch concerning multicasting but i have no clue (and don't ...

I have what is hopefully a simple question.  I'd like to know if any of the small business switches (e.g., the SRW2024) will work with AT&T uverse.I have my house wired for gigabit, and am getting uverse installed this week.  I have one gigabit (rj45...

Hi,I try to configure an etherchannel trunk but I´ve no success.So I need a step by step guide to configure the trunk.I´ve 6 vlans defined on the Switch:VLAN1VLAN121VLAN122VLAN123VLAN999Now I need an etherchannel as trunk (ports g7 and g19) with the ...

Just purchased 1/2 a dozen SG100-24 switches which I was planning to use in our switch rack and uplink into our HP Procurve switching backbone ... but when I connected port 24 up ... nada ... nothing ... doesn't light up ... no traffic.In the past we...

Hi,We're facing a strange issue with one of our SRW2024 Switches.We already have many of them in production with the following configuration :interface vlan 2ip address 10.10.10.1 255.255.0.0 Some ports being on the same VLAN, some in access mode, so...

I'm managed switch no0b and I'm unfortunately running into a wall configuring it. Some background: My IP phones and VOIP service is all provided by an offsite company, however for cost purposes they no longer provide networking support for my office ...