07-10-2013 12:31 PM - edited 03-07-2019 02:20 PM
Hello,
i have a 2901 router (IOS version 15.3) and after i plugged the Ethernet module into one of its EHWIC i found that the router doesn't detect it and the other router detected it and no traffice is passed through it. does any one know why that happened. BTW this Router should support 2 4-port Cisco Gigabit Ethernet EHWICs.
thank you!
Makar
07-10-2013 02:55 PM
Post the entire bootup process.
07-11-2013 08:22 AM
Hi Leo,
please find the boot process output that pasted below.
BTW when i connect two hosts on the same HWIC they reach each other but the problem is when i connect them on different HWIC cards. thanks
IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x5e65400
Self decompressing the image : ############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################ [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
HWIC Slot 2 0x00200000
HWIC Slot 3 0x00200000
Onboard devices &
buffer pools 0x0228F000
-----------------------------------------------
TOTAL: 0x0268F000
Rounded IOMEM up to: 40Mb.
Using 7 percent iomem. [40Mb/512Mb]
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 26-Feb-13 03:42 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco CISCO2901/K9 (revision 1.0) with 909312K/40960K bytes of memory.
Processor board ID FTX145000GS
8 FastEthernet interfaces
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
07-11-2013 11:57 AM
Hi everyone,
i got the solution for this problem. and discovered that:
Only 2 HWIC or EtherSwitch network modules can be used in this platform and to let them communicate with eachother we have to stack them physically by an ethernet cable to use one port on each card as a trunk. and also we have to issue the command switchport stacking-partner on these trunk port to let the two HWIC cards have L2 connectivity.
please rate if you find it helpful. thanks!
Labib
07-11-2013 12:01 PM
Very helpful Labib,
Thank You for the update (+5)
07-11-2013 12:14 PM
please access this link below for the full solution. thanks!
Labib
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide