06-28-2013 06:16 AM - edited 03-07-2019 02:08 PM
HI all. I have a Cisco 891W ISR with the embedded AP801 inside. I seem to have forgotten the password for it. I can get into the router no problem, but must have at some point disabled the web server for the AP as I can't get to it that way, so need to go there via CLI it seems. As htere is o console port for the embedded AP, I can only imagine there's a means to reset it by command line. I hope!
Please help, thank you.
Solved! Go to Solution.
06-28-2013 06:10 PM
Remote into your router. Issue the ENABLE command "service-module wlan-ap 0 reset bootloader". The AP will reboot into ROMmon.
Then remote into your AP using the command "service-module wlan-ap 0 session" and change the filename of the running-config.
When you've done that, enter "boot" and the AP will reboot into factory default. Issue the next command "copy start run". Then go "config t" and change the password and save the config. Done.
06-28-2013 06:10 PM
Remote into your router. Issue the ENABLE command "service-module wlan-ap 0 reset bootloader". The AP will reboot into ROMmon.
Then remote into your AP using the command "service-module wlan-ap 0 session" and change the filename of the running-config.
When you've done that, enter "boot" and the AP will reboot into factory default. Issue the next command "copy start run". Then go "config t" and change the password and save the config. Done.
08-07-2013 09:01 AM
I have the same issue.
please tell me how could we "Then remote into your AP using the command "service-module wlan-ap 0 session" and change the filename of the running-config." while we can't login to it! in order to remote into it you'd still need the user/pass for the AP.
08-07-2013 03:35 PM
Did you try this?
service-module wlan-ap 0 reset default-config
and then reset the AP module
service-module wlan-ap 0 res
Jawad
08-14-2013 08:35 AM
Hi all. I'm still not yet able to test. Testing the solutions involves dsiconnecting various wi-fi connected users onsite so it's a tough scheduling problem. I will make sure I post bacxk to this thread as soon as I can - keep any additional suggestions coming though - I can queue all of them to try!
Thank you as well.
08-30-2013 12:09 PM
Ok I have successfully accomplished the task. Hwoever oddly the steps were different. Since it was first in the sequential order of thread replies, I first tried Leo's suggestion. Step 1 which did the "reset bootloader" seemed to go well. However i did not know how to rename running-config. While at the AP's prompt, dir showed 4 filesystems yet none had nvram, so I tried to access flash[0] and it said permission denied. Eitehr way, I restarted the AP by entering "boot". This brought it up to a default configuruation already.
I then copied start run, found that it was all default stuff anyway, so I upgraded flash and input my own config from a previous config template I had created for these APs.
So I didn't get a chance to the "reset default-config". However, what's the difference between the two? (no problme if nobody gets a chance to answer, just curious).
09-06-2013 07:03 AM
I opened a ticket with cisco and they concluded that this was a hardware issue and the unit needs to be replaced.
09-10-2013 11:15 AM
That's odd but I imagine there were things happening differently between your and my problem, else it would be strange that they replace hardware. A new router means all new configuration so I guess it's still a solution for you as well
02-14-2019 02:25 AM
Thanks dude, you're the best!
That command "default-config" best ever.
Saved me from the hell that is Cisco service-modules with AP's.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide