Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

I am trying to mirror traffic from one router to another with below config:R1:R1#sh run | sec monitor  monitor session 1 type erspan-source source interface Gi0/0/3 rx destination  erspan-id 100  ip address 192.168.0.0  origin ip address 192.168.0.1R...

I have two exchange 2010 mail servers behind a c1800isr.  Mail server two has a static nat as belowip nat inside source static <inside address> <outside address> route-map nonat_static.  We want mail server two to send mail out the outside address sp...

mialbert by Level 1
  • 515 Views
  • 3 replies
  • 0 Helpful votes

Hi,Is the sim card included inside the PCEX-3G-HSPA or is this an additional piece added seperately?Thanks, Pat.I posted this before on another category and it wasn't getting any hits so I thought it might do better here.Sorry for the repeat.

Hi, Guys,We need help with some recommendation of which Cisco device we should purchase: Environment: 1, Will be used in Data Center, Racked Mounted 2, 6 Physical Supermicro Servers and Negear NAS connected via Cisco switchFeatures we neede: 1, Netwo...

I believe I have the steps done at the IOS to config the WAN port for SSH, but I still can't connect to it.  I have "logging console 7" on so I am able to see that the router is dropping my TCP session requests.  I figure this is just the built-in zo...

cluovpemb by Level 1
  • 2609 Views
  • 11 replies
  • 0 Helpful votes

Resolved! dhcp snooping

On our network , an edge switch which is in a stacked mode has been configured with below on two ports,interface fa0/5switchport trunk encapsulation dot1q switchport trunk allowed vlan 11,21,5switchport mode trunk storm-control broadcast level 15.00 ...

suthomas1 by Level 6
  • 903 Views
  • 1 replies
  • 0 Helpful votes

Hi allI have a catalyst 6506E (WS-C6506-E) with a SUP2T supervisor (VS-S2T-10G) card and a 10G interface card (WS-X6816-10G-2T) + DFC4.I have configured an etherchannel to another switch with the 2 10Giga ports of the SUP2T card and 2 10giga ports of...

cminard by Level 1
  • 3335 Views
  • 2 replies
  • 0 Helpful votes

Hi All,Hope you can help with this one or certainly point me in the right direction.We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of ...

Hi, Let's talk about QoS on wireless network.I am not sure how to proper deploy a QoS in wireless network.Based on Cisco documents. looks it create several SSIDs and seperate clients by SSID.How to do it? we may mixed high priority and low priority a...

I understand that the PCEX-3G-HSPA requires and a sim card. I also have a PCEX-3G-CDMA-V. Does this require a sim card as well? And if so, where is  the sim card installed?Thanks, Pat  

HiWe have a Cisco 4507R switch with sup V. This switch fan tray has partial problem .No light in fan tray. We got another fan tray. Can any one tells me is it hot swappable?What procedure should I flow without any interruption our live network?Would ...

aminulnt by Level 1
  • 4912 Views
  • 4 replies
  • 0 Helpful votes