06-25-2022 02:06 AM - edited 06-26-2022 08:14 PM
Hello,
I accidentally factory reset my Cisco C9300-24T. Then I tried to fix it with emergency installation.
Then I got this problem:
Solved! Go to Solution.
06-25-2022 10:07 AM
what i noticed here, is you are not reading the suggested methods in the thread - do 1 step at a time, spend reading the docs we suggest, if you looking get back the switch into working. connect console, capture all the information in text file and post here, so we can understand better - what is wrong and where it going wrong. suggest to start with 16.9.X or 16.12 for recovery, I have posted the URL have good steps.
if not Raise the TAC case.
06-25-2022 02:10 AM - edited 06-25-2022 02:29 AM
@iMufiyan wrote:
Package file does not have a valid SHA-1 digest
The file is corrupt.
Download the file again, check/compare the MD5 hash against the one found in the Cisco website.
06-25-2022 05:10 AM - edited 06-25-2022 05:23 AM
I've allready test this ios :
cat9k_iosxe.17.06.03.SPA.bin :fail
cat9k_iosxe.16.09.01.SPA.bin :fail
cat9k_iosxe.16.09.04.SPA.bin :fail
cat9k_iosxe.16.12.07.SPA.bin :fail
cat9k_iosxe.17.08.01.SPA.bin :fail
Still the same
My bootflash and flash directory is also empty.
switch: dir
usage:
dir <path-to-directory>
supported filesystem(s):
flash: ro flash
bootflash: ro system partition
usbflash0: rw front-panel USB
usbflash1: rw back-panel USB
PLATFORM_TYPE C9300 speed 9600
Booting Recovery Image 16.6.1
Initiating Emergency Installation of bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin
Reading bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin...
Validating bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin...
Installing bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin....
Package file does not have a valid SHA-1 digest
Emergency Install failed - bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin is not supported on this platform
Will reboot now
06-25-2022 06:03 AM
As i remember Cat 9300-24T ship with 16.9.X or 16.12.X version, so it can not go below that version to work.
Download the image, check the MD5 checksum : follow below guide :
06-25-2022 06:38 AM
@iMufiyan wrote:
bundle usbflash0:cat9k_iosxe.16.06.01.SPA.bin is not supported on this platform
You started this thread with attempting to load 16.9.1. Now, you are trying to load 16.6.1.
So answer this: WTF are you trying to do?
06-25-2022 09:12 AM
I just want to turn the router back on to normal again.
so i tried different ios. and nothing is installed successfully.
I've tried all the suggestions you gave, but nothing works.
Trust me, I'm also confused what im going to do next.
06-25-2022 10:07 AM
what i noticed here, is you are not reading the suggested methods in the thread - do 1 step at a time, spend reading the docs we suggest, if you looking get back the switch into working. connect console, capture all the information in text file and post here, so we can understand better - what is wrong and where it going wrong. suggest to start with 16.9.X or 16.12 for recovery, I have posted the URL have good steps.
if not Raise the TAC case.
06-25-2022 05:50 PM
Remove all fibre optic NM cards, cold-reboot the switch (pull the power).
When the switch boots into ROMMON, post the complete output (including serial numbers) to the following commands:
06-26-2022 08:07 PM
06-26-2022 11:14 PM
@iMufiyan wrote:
BYPASS_STARTUP_CONFIG=1
WTF.
Enter "BYPASS_STARTUP_CONFIG=0"
And then post the complete output to the command "dir usbflash0:".
06-25-2022 07:35 PM
hi,
can you try
switch: boot usbflash0:cat9k_iosxe.16.09.01.SPA.bin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide