09-10-2019 05:15 AM
Buen día, alguien me puede apoyar con los siguientes loggs:
Sep 9 15:20:50.929 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:50.929 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:51.938 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
Sep 9 15:20:52.939 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:52.940 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:54.062 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
Sep 9 15:20:54.949 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:54.949 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:55.958 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
Sep 9 15:20:56.970 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:56.970 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:57.978 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
Sep 9 15:20:58.979 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:20:58.979 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:21:00.998 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
Sep 9 15:21:03.018 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:21:03.019 MEX: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
Sep 9 15:21:04.051 MEX: %ILPOWER-7-DETECT: Interface Gi1/0/18: Power Device detected: IEEE PD
interface GigabitEthernet1/0/18
description vlan 193 users
switchport access vlan 193
switchport mode access
switchport voice vlan 100
switchport port-security maximum 2
switchport port-security maximum 1 vlan access
switchport port-security maximum 1 vlan voice
switchport port-security
speed 100
duplex full
trust device cisco-phone
auto qos voip cisco-phone
spanning-tree portfast
spanning-tree bpduguard enable
service-policy input AutoQos-4.0-CiscoPhone-Input-Policy
service-policy output AutoQos-4.0-Output-Policy
end
Switch Ports Model Serial No. MAC address Hw Ver. Sw Ver.
------ ----- --------- ----------- -------------- ------- --------
1 32 WS-C3850-24P-S FOC1909X0HM c800.8453.6580 V05 03.06.08E
09-10-2019 05:21 AM
09-10-2019 05:48 AM
Hi Leo, I share the requested information:
sh cable-diagnostics tdr int g1/0/8
TDR test last run on: September 10 07:42:35
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi1/0/8 100M Pair A 1 +/- 1 meters N/A Open
Pair B 0 +/- 1 meters N/A Open
Pair C 0 +/- 1 meters N/A Open
Pair D 0 +/- 1 meters N/A Open
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- -----------------------------------------
* 1 32 WS-C3850-24P 03.06.08E cat3k_caa-universalk9 INSTALL
09-10-2019 06:35 AM
Can you also provide out put of below command.
show power inline
09-10-2019 07:02 AM
Hi, I had to set the "power inline never" command for stop the logg.
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 720.0 13.2 706.8
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 auto off 0.0 n/a n/a 30.0
Gi1/0/2 auto off 0.0 n/a n/a 30.0
Gi1/0/3 auto on 9.5 IP Phone 8961 4 30.0
Gi1/0/4 auto off 0.0 n/a n/a 30.0
Gi1/0/5 auto off 0.0 n/a n/a 30.0
Gi1/0/6 auto off 0.0 n/a n/a 30.0
Gi1/0/7 auto off 0.0 n/a n/a 30.0
Gi1/0/8 auto off 0.0 n/a n/a 30.0
Gi1/0/9 auto off 0.0 n/a n/a 30.0
Gi1/0/10 auto off 0.0 n/a n/a 30.0
Gi1/0/11 auto on 3.7 IP Phone 7841 1 30.0
Gi1/0/12 auto off 0.0 n/a n/a 30.0
Gi1/0/13 auto off 0.0 n/a n/a 30.0
Gi1/0/14 auto off 0.0 n/a n/a 30.0
Gi1/0/15 auto off 0.0 n/a n/a 30.0
Gi1/0/16 auto off 0.0 n/a n/a 30.0
Gi1/0/17 auto off 0.0 n/a n/a 30.0
Gi1/0/18 off off 0.0 n/a n/a 30.0
Gi1/0/19 auto off 0.0 n/a n/a 30.0
Gi1/0/20 auto off 0.0 n/a n/a 30.0
Gi1/0/21 auto off 0.0 n/a n/a 30.0
Gi1/0/22 auto off 0.0 n/a n/a 30.0
Gi1/0/23 auto off 0.0 n/a n/a 30.0
Gi1/0/24 auto off 0.0 n/a n/a 30.0
09-10-2019 11:50 PM
09-11-2019 05:23 AM
you are right :P , I´m sorry:
TDR test last run on: September 11 07:13:00
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi1/0/18 100M Pair A N/A N/A Not Completed
Pair B 0 +/- 1 meters Pair A Normal
Pair C 0 +/- 1 meters N/A Normal
Pair D 0 +/- 1 meters N/A Normal
Note: the log disappeared when i set the line "power inline never" on the interface g1/0/18, but I want to know the root cause.
09-11-2019 11:44 PM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide