Hi, There is confusion. Yesterday I had discussed with Cisco SE and he told me that there is a possibility of Cisco Instant access on Catalyst 9K/5K with DNA/SD-access license without DNA center and ISE. Can anyone help me what is this technology and...
Forum Posts
Hi, I need to connect a server with a switch port? What should I configure for that port?which one is better to configure in switch port Access port or trunk port ? If I connected server port with switch access port will my switch port receive...
how many actual HSRP Instances can be configured on cisco switch C9300-48T-A | CAT9300 Universal image. I have been through number of documents, but no luck . everyone has given no. of groups supported by version 1 & 2 & i am not looking out for that...
Resolved! Debug logging events not showing up
I am trying to debug IBNS 2.0 on one of my switchports when a non-responsive device is connected.I have the following debug logging enabled: testswitch#sho debug General OS: AAA Authentication debugging is on AAA Authorization debugging is on A...
Hello Community, In the process of upgrade Cisco 6506-E, with the aim of moving from 151-1.SY2 to 155-1.SY4, the supervisors completed the upgrade as expected, however on completion of the upgrade the SPF line Card didn't come online fully. The SFP ...
Hello!Have a problem with LACP between C4510 and HP ProLiant DL360 Gen9.There two 10GE fiber ports between SW and server.Config C4510: interface TenGigabitEthernet5/1switchport access vlan 131switchport mode accesschannel-group 5 mode active...interf...
Hello community,after upgrading about 35 Catalyst 2960 and Catalyst 2960S to IOS 15.0(2)SE2, we experience a memory leak on several switches. After some days / weeks the switches are not accessible via Console/Telnet/SSH/Web any more. Only SNMP seems...
Hi All, I have the same problem with another version, 15.0(2)SE7. Can someone help me and let me know if have experienced this issue with the version 15.0(2)SE7? Regs,Bruno Siqueira
Hello. Please help me with the default ip address of switch cisco ws-ce500-24lc. I am trying to configure it using ethernet cable and i have used 192.168.1.2 but i have failed. Please help me
Resolved! VRF not supported in 3650
Hi Guys, need help and suggestion I am trying to using VRF for my company on serveal 3650 switches, after I input " ip vrf vpn1" command, the system pop up as " the feature does not supported " I am using a WS-C3650-24TD-S IP BASE switch with Image: ...
Dear All, I have a quick requirement for adding more additional switch, can I know : What is the maximum number of switches that can be stacked using Cisco StackWise Virtual using 9000 Series switches ? and recommended firmware it supports ? Regards...
Consider the following escenario: a small enterprise network. One fortigate, 3 cisco 3560 multilayer switches, and several (around 8 or so) cheaper L2 switches (TP-link and Dlink). All users are connected to the L2 switches, which in turn are connect...
Hello all,I support a customer network which has at it's core a 4507R+E with dual WS-X45-SUP8L-E/2 supervisors. We have 2 WS-X4624-SFP-E blades which support 1G connections using either LX or SX Gbics. First, I am fairly confindent, but I would still...
I am confused about the below answer.I was under the impression that a port is put into the discarding state following the below steps in order:1) Cost to root bridge2) Lowest BID3) Port priority4) Port ID In the below question, shouldn't the answer ...
Resolved! Moderate CPU, slow ping
Have an odd problem that seems to get worse over time. Ping times across vlans gets progressively slower until packets start dropping on workstations/servers. Seems like a monthly occurrence. Include a putty log of output from various show cpu/plat...
