Configure VLANs on SF 300 to work with 2960S

[m.junghage]

Hi,

I'm pulling my hair in order to make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.

I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.

Any help would be greatly appreciated!

I've partially described the enviroment below.

VLANs

Data                  VLAN 10:    192.168.10.0

Management      VLAN 50:    10.20.30.0

Voice                 VLAN 100:  10.10.10.0   

2960S

Gi1/0/1-20 in VLAN 10

Gi1/0/21-30 in VLAN 100

Gi1/0/47-52 in TRUNK, allowed VLAN 10, 50, 100 (Connected to 6 SF300 switches)

SF300

Fa0/1-24 in VLAN 100

Gi0/1 in TRUNK, allowed VLAN 50,100 (Connected to 2960S)

SF300

Gi0/1-30 in VLAN 10

Gi0/31-44 in VLAN 100

Gi0/45-48 in TRUNK, allowed VLAN 10,50, 100 (Connected to 2960S and 3 other SF300 switches)

Regards
Markus

[Somasundaram Jayaraman]

Hi

I found a administrative guide for you.

http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf

i hope this might help you in acheiving your desired configuration.

Cheers

Somu

Rate helpful posts

[m.junghage]

Thanks for the help! I've sort of forgot this thread and wanted to give an update.

I actually didn't get it working using the web gui even with the manual I struck out. I googled around a bit and found out the newer firmware versions supported a IOS like CLI. I upgraded and got a lovely CLI and a couple of minutes after I got VLAN trunking working.

Conclusion: Scrap web gui's and give me CLI for everything!

[palmermichael]

What settings did you end up using?

[m.junghage]

Here's my config that worked with the IOS CLI like firmware. I've removed configuration that have nothing to do with the interface/vlan config. I hope it can offer some help.

interface range  gi1-2,gi4

switchport forbidden default-vlan

exit

vlan database

vlan 10,50,100

exit

interface vlan 10

name Data

exit

voice vlan id 100

voice vlan state oui-enabled

voice vlan cos 6 remark

voice vlan oui-table add 000050 Aas_____________________

voice vlan oui-table add 0001e3 Siemens_AG_phone________

voice vlan oui-table add 00036b Cisco_phone_____________

voice vlan oui-table add 00085d Aastra_IP_phone_________

voice vlan oui-table add 00096e Avaya___________________

voice vlan oui-table add 000fe2 H3C_Aolynk______________

voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone

voice vlan oui-table add 00d01e Pingtel_phone___________

voice vlan oui-table add 00e075 Polycom/Veritel_phone___

voice vlan oui-table add 00e0bb 3Com_phone______________

interface vlan 10

ip address 192.168.10.222 255.255.255.0

exit

interface vlan 1

no ip address dhcp

exit

interface fastethernet23        #Interface Fa01-23 is configured like this.

switchport mode access

switchport access vlan 100   #Access port for voice vlan

exit

interface fastethernet24

switchport mode access

switchport access vlan 10     #Access port for data vlan

exit

interface gigabitethernet2

switchport mode access

switchport access vlan 10

switchport general pvid 4095     #STP Link to data vlan access switch

exit

interface gigabitethernet3

switchport trunk allowed vlan add 10,50,100    #SFP trunk to core-switch

exit

interface gigabitethernet4

switchport mode access

switchport access vlan 10        #STP Link to data vlan access switch

exit

interface vlan 10

name Data

exit

interface vlan 50

name Management

exit

interface vlan 100

name Voice

[Mohamed OTHMAN]

Hi

I'm facing same problem like you!!

Please can tell me which ios you installed? and if possible the link to download!

THANK's