cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1480
Views
0
Helpful
1
Replies

Dows Cisco Routers 2921 supports WIC Cards?

I have trouble to install a Frame Relay service because the vendor sold me WIC cards but i think 2921 only supports HWIC cards

Here's the output of the show diag:

Router Llano Mall
ag321-acc-rou-01#sh diag | b WIC Slot 1:
         WIC Slot 1:
         Serial 2T (12in1)
         WIC module not supported/disabled in this slot
         Hardware revision 1.0           Board revision B0
         Serial number     32098957      Part number    800-03181-02
         FRU Part Number     WIC-2T=          
         Test history      0x0           RMA number     00-00-00
         Connector type    PCI
         EEPROM format version 1
         EEPROM contents (hex):
           0x20: 01 12 01 00 01 E9 CA 8D 50 0C 6D 02 00 00 00 00
           0x30: 58 00 00 00 04 04 08 00 FF FF FF FF FF FF FF FF

Router Cumaná
ag521-acc-rou-01#sh diag | b WIC Slot 0:     
         WIC Slot 0:
         HWIC Serial 2T WAN daughter card
         Hardware Revision        : 2.0
         Top Assy. Part Number    : 800-34379-01
         Board Revision           : A0
         Deviation Number         : 115024
         Fab Version              : 02
         PCB Serial Number        : FOC15023T8C
         RMA Test History         : 00
         RMA Number               : 0-0-0-0
         RMA History              : 00
         Fab Part Number          : 28-8141-01
         Product (FRU) Number     : HWIC-2T
         Version Identifier       : V03
         CLEI Code                : COUIA1RCAB
         EEPROM format version 4
         EEPROM contents (hex):
           0x00: 04 FF 40 05 89 41 02 00 C0 46 03 20 00 86 4B 01
           0x10: 42 41 30 88 00 01 C1 50 02 02 C1 8B 46 4F 43 31
           0x20: 35 30 32 33 54 38 43 03 00 81 00 00 00 00 04 00

           0x30: 85 1C 1F CD 01 CB 87 48 57 49 43 2D 32 54 89 56
           0x40: 30 33 20 D9 02 40 C1 C6 8A 43 4F 55 49 41 31 52
           0x50: 43 41 42 FF FF FF FF FF FF FF FF FF FF FF FF FF
           0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
           0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Is there any command or any form that i can use this card to implement frame relay?

Thanks in advance

Alejandro

1 Accepted Solution

Accepted Solutions

johnlloyd_13
Level 9
Level 9

It looks like it's unsupported and a 2921 ISR G2 would accept an HWIC-2T instead.

http://www.cisco.com/en/US/products/ps10537/products_relevant_interfaces_and_modules.html#serialwan

Sent from Cisco Technical Support iPhone App

View solution in original post

1 Reply 1

johnlloyd_13
Level 9
Level 9

It looks like it's unsupported and a 2921 ISR G2 would accept an HWIC-2T instead.

http://www.cisco.com/en/US/products/ps10537/products_relevant_interfaces_and_modules.html#serialwan

Sent from Cisco Technical Support iPhone App

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: