06-12-2017
04:15 AM
- last edited on
03-25-2019
04:43 PM
by
ciscomoderator
is it true that spanning tree loop never occur if all links are using port channel?
if it is true, does it mean that no need to apply loop guard and root guard for all port channels?
06-12-2017 04:41 AM
is it true that spanning tree loop never occur if all links are using port channel? no
You can still use loopguard on an etherchannel you need to be aware as an example in pvst if you get unidirectional failure it make the po inconsistent and down for all links for that particular vlan when the issue occurs, so if link 1 fails out of 4 links then the 4 links become down state for that vlan for stp but it will still operate for other vlans and not physically shut the po
06-12-2017 08:12 AM
juniper engineer told me that all links are port channel from juniper with cisco switch,
so spanning tree loop impossible to occur, master and backup juniper switch are all port channels, and to cisco switch are all port channel too
i am thinking whether this is only true in mixed juniper and cisco topology but not in topology if all cisco switch, is it true?
06-12-2017 08:20 AM
I think what he meant was when 2 switches have multiple links together between the switches yes you can easily cause a loop if stp is not in place as traffic will loop around at layer 2
if you bundle all the links together there is only 1 path like having 1 physical link between the 2 switches so there cant really be a loop , that would only be the case though if there were ONLY 2 switches directly connected to each other by port-channels , doesn't matter whether cisco or juniper stp is a feature available on multiple platforms and works the same way generally on each as its a link loop avoidance feature
if you had multiple switches same broadcast domain with multiple port channels a loop could still form if not planned correctly at stp
06-12-2017 10:21 AM
in our case, they said our case is to not separate vlans into different STP,
mixed with cisco switch, it can not use MSTP, it need RSTP
06-12-2017 11:10 AM
MSTP is a "better" variant of RSTP.
Juniper supports RSTP, but again, (I recall) they don't support per VLAN RSTP.
06-12-2017 04:30 PM
they said that MSTP approach is not feasible if connecting with juniper
06-12-2017 05:10 PM
if distribution layer switch is juniper , access switch is cisco
is it true that cisco switch not need to configure loop guard at etherchannel which are root port ?
if distribution layer switch is cisco , access switch is juniper
is it true that cisco switch not need to configure root guard at etherchannel which trunk to juniper?
are loop guard and root guard for single link and one port only?
i had experience in creating a loop at distribution layer when connect a switch to access switch which had not configured root guard at trunk port
i remembered that the distribution layer using etherchannel too
06-13-2017 05:19 AM
they said that MSTP approach is not feasible if connecting with juniper
MSTP should works between cisco and juniper switches its on there ex series switches
makes no difference whether its juniper or Cisco you need to just look at the feature and plan out stp correctly based on your network not its vendor type , Root guard is best deployed towards ports that connect to switches which should not be the root bridge
is it true that cisco switch not need to configure root guard at etherchannel which trunk to juniper?
root guard and loop guard are optional commands you don't have to use them but you can if you want to
06-13-2017 02:41 AM
Who are "they"?
What are the actual devices?
06-12-2017 04:57 PM
it seems that loop guard should not enable in port channel because it will block the whole logical link
if loop guard should not enable in port channel,
then can it imply loop never occur in port channel?
if distribution layer switch is juniper , access switch is cisco
is it true that cisco switch not need to configure loop guard at etherchannel which are root port ?
if distribution layer switch is cisco , access switch is juniper
is it true that cisco switch not need to configure root guard at etherchannel which trunk to juniper?
06-12-2017 04:42 PM
all trunk port using port channels, one port channel is connected with backup switch
another port channel is connected with cisco switch
it seems that loop guard should not enable in port channel because it will block the whole logical link
06-12-2017 09:43 AM
No, STP and port-channel needs don't differ between Cisco and Juniper, either on only their equipment or between the two vendors.
However, Cisco supports PVSTP and Juniper doesn't, so mixing them, at L2, is a bit of fun. Both, though, should support MST.
06-12-2017 04:47 AM
Hi
I think a proper STP configuration is always required to avoid layer 2 loops, independent if you are using port channel or not, please check this link:
https://supportforums.cisco.com/discussion/11059606/how-does-loop-form-misconfigured-etherchannel
Hope it is useful
:-)
06-12-2017 06:13 AM
I cant see how that could be the case,
unless all physical ports on a switch form a port channel to a single remote switch. Port channels still run STP but pretty much leave the physical port that constitute a single port channel out of the equation. meaning only the port channel is calculated as a single STP port (the cost can vary based on how many physical ports are in the same port channel)
please rate if useful
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide