My knowledge is very basic so please bear me with me.
I just bought a CISCO892W-AGN-E-K9. This device has two indepent wireless antenna's, an 8 port internal switch plus two WAN links, 1 Gigabit Ethernet and a fast ethernet port and finally a backup ISDN line. I am not going to use the ISDN.
I am trying to get start with some very basic activity which is enabling the Gigabit Ethernet (or the FE, I don't care). My plan was to either give it a static IP address or a DHCP address. A DHCP server is present.
The first issue is that the WAN ports don't seem to be accessible. If I connect either of the WAN ports and power up the device they don't seem to be enabled, sending out DHCP or the like etc.
So I changed strategy and connected one of the internal switch ports. That works. It apparently does an DHCP over the 8 port switch and it does get an IP and so I can use telnet to login to the device. I am missing some converter so I haven't been able to use the console port.
So when I log in into the device I do find the GE but I can't find the FE or the switch port.
cisco-ap#show interfaces summary
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
------------------------------------------------------------------------
* BVI1 0 0 0 0 2000 2 0 0 0
Dot11Radio0 0 0 0 0 0 0 0 0 0
Dot11Radio1 0 0 0 0 0 0 0 0 0
* GigabitEthernet0 0 0 0 0 3000 3 0 0 0
So it seems that the GE interface is connected to the internal switch. Where are my wlan ports?
Any help is appreciated. Just to be sure I'll append the show interfaces output and the running config (which is the default config).
Fred
If I ask for the a list of interfaces using the ? I get:
cisco-ap#show interfaces ?
Async Async interface
BVI Bridge-Group Virtual Interface
CDMA-Ix CDMA Ix interface
CTunnel CTunnel interface
Dialer Dialer interface
Dot11Radio IEEE 802.11 WLAN
GigabitEthernet GigabitEthernet IEEE 802.3z
Loopback Loopback interface
Multilink Multilink-group interface
Null Null interface
Tunnel Tunnel interface
Vif PGM Multicast Host interface
Virtual-Dot11Radio Virtual Dot11 Interface
Virtual-PPP Virtual PPP interface
Virtual-Template Virtual Template interface
Virtual-TokenRing Virtual TokenRing
accounting Show interface accounting
counters Show interface counters
crb Show interface routing/bridging info
dampening Show interface dampening info
description Show interface description
irb Show interface routing/bridging info
mac-accounting Show interface MAC accounting info
mpls-exp Show interface MPLS experimental accounting info
precedence Show interface precedence accounting info
rate-limit Show interface rate-limit info
stats Show interface packets & octets, in & out, by switching path
summary Show interface summary
switching Show interface switching
| Output modifiers
<cr>
The running config:
Current configuration : 2997 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco-ap
!
logging rate-limit console 9
enable secret 5 $1$cKpt$CwBHMRNrOKECVze4A5o66.
!
no aaa new-model
!
!
dot11 syslog
!
!
username cisco privilege 15 secret 5 $1$SGEn$qSAJ1dmxlz/GhYKMLjG4T.
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
!
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
banner exec ^CC
% Password change notice.
-----------------------------------------------------------------------
Default username/password setup on AP is cisco/cisco with privilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
-----------------------------------------------------------------------
^C
banner login ^CC
% Password change notice.
-----------------------------------------------------------------------
Default username/password setup on AP is cisco/cisco with privilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
-----------------------------------------------------------------------
^C
!
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
!
cns dhcp
end
