Port-channel Down LACP nexus 93180 and Ubuntu server

[admin@atrinnet.net]

Hi i run LACP port-channel between cisco 93180 and ubuntu server 22 LTS

on ubuntu 802.3 ad layer 2+3 config

on cisco lacp with force mode active

Channle-group is up by add to monitor session 1 destanation inteface

frequency every 1 min is Down and on the physical port on switch initial and again up

test hardware is ok

show logging say to me port up and down

any idea to help me ?

BIOS: version 07.69
NXOS: version 10.3(4a) [Maintenance Release]
BIOS compile time: 04/07/2021
NXOS image file is: bootflash:///nxos64-cs.10.3.4a.M.bin
NXOS compile time: 11/5/2023 12:00:00 [11/02/2023 04:27:01]

[balaji.bandi]

Channle-group is up by add to monitor session 1 destanation inteface

recently you asked question and we mentioned as limitation or is this something new ?

https://community.cisco.com/t5/switching/span-by-destanation-port-channel/m-p/5130363#M565859

[admin@atrinnet.net]

Hi ion

This link about n3000 series and you answer limitation of n3000 donnot set destanation port only physical port

this topic about nexus 9K series that can be destanation port in monitor session as port-channel

But port channel so up and down

[balaji.bandi]

what model of Nexus 9K

Guidelines and Limitations for SPAN

• FEX and SPAN port-channel destinations are not supported on the Cisco Nexus 9500 platform switches with an -EX or –FX type line card.

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/system_management/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Guide/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Gui...

Note : if this connected to Linux, make since port to span all the traffic, instead of Trunk or port-channel.

Or you can connect to 2 different ports to Linux using different destination port as individuals if you looking more redundancy here.

[admin@atrinnet.net]

switch 93180 EX

Yes connected to the linux

port-channel

config 

switch monitor

you say port-channel config as Trunk or Access mode ?

[balaji.bandi]

there is limitation may be spend some time and read document give you direction

if i were you source acn be port-channel

destination use physical port which is connected to Linux - there is no configuration required on the destination port default the configuration of the port and use monitor port, so in Linux you can run any sniffer like tcpdump or wireshark you should get desire outcome.

[admin@atrinnet.net]

In thie docummnet mirrotr port 10G to port 40gbps

I want mirrot port-chaneel 1 to port-channel 2

[Georg Pauwen]

Hello,

which hash policy do you have configured on the Ubuntu ?

[admin@atrinnet.net]

network:
bonds:
bond0:
interfaces:
- ens2f0
- ens2f1
parameters:
lacp-rate: slow
mode: 802.3ad
transmit-hash-policy: layer2+3

[Georg Pauwen · Accepted solution]

Hello,

what if you change the lacp-rate to 'fast' ?

[admin@atrinnet.net]

On the switch only this log 2024 Jun 16 04:16:39 Router-Edge-Sepehr %SYSLOG-1-SYSTEM_MSG: Logging logfile (m
essages) cleared by user
2024 Jun 16 04:16:55 Router-Edge-Sepehr %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-ch
annel1: first operational port changed from Ethernet1/23 to Ethernet1/22
2024 Jun 16 04:16:55 Router-Edge-Sepehr %ETH_PORT_CHANNEL-5-PORT_DOWN: port-chan
nel1: Ethernet1/23 is down
2024 Jun 16 04:16:55 Router-Edge-Sepehr %ETHPORT-5-IF_DOWN_INITIALIZING: Interfa
ce Ethernet1/23 is down (Initializing)
2024 Jun 16 04:16:57 Router-Edge-Sepehr %ETHPORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_
DOWN: Interface port-channel1 is down (No operational members)
2024 Jun 16 04:16:57 Router-Edge-Sepehr %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-ch
annel1: first operational port changed from Ethernet1/22 to none
2024 Jun 16 04:16:57 Router-Edge-Sepehr %ETH_PORT_CHANNEL-5-PORT_DOWN: port-chan
nel1: Ethernet1/22 is down
2024 Jun 16 04:16:57 Router-Edge-Sepehr %ETHPORT-5-IF_DOWN_INITIALIZING: Interfa
ce Ethernet1/22 is down (Initializing)
2024 Jun 16 04:16:57 Router-Edge-Sepehr %ETHPORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_
DOWN: Interface port-channel1 is down (No operational members)

Any idea ???

[admin@atrinnet.net]

ON ubuntu have this info abound bonding

cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Peer Notification Delay (ms): 0

802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
System priority: 65535
System MAC address: c6:b4:7e:41:93:e1
Active Aggregator Info:
Aggregator ID: 2
Number of ports: 2
Actor Key: 15
Partner Key: 32768
Partner Mac Address: 00:3a:7d:96:6f:55

Slave Interface: ens2f1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 38:ea:a7:15:81:89
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: c6:b4:7e:41:93:e1
port key: 15
port priority: 255
port number: 1
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 00:3a:7d:96:6f:55
oper key: 32768
port priority: 32768
port number: 341
port state: 61

Slave Interface: ens2f0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 38:ea:a7:15:81:88
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: c6:b4:7e:41:93:e1
port key: 15
port priority: 255
port number: 2
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 00:3a:7d:96:6f:55
oper key: 32768
port priority: 32768
port number: 345
port state: 61