cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2961
Views
5
Helpful
6
Replies

Require EIGRP Full Functionality on 4506E switch - IOS issue

Hello Everyone,

I have a question based on switches IOS. Right now i am working on one setup which has two 4506-E switches with SUP 7E and i want to run EIGRP on this two switches with is connecting to Internet router and PSTN router in full mesh design

When i enable EIGRP on router it works fine but on this switches it automatically enable the command under EIGRP for stub routing as shown in below config.

router eigrp 100

network x.x.x.x

eigrp stub connected summary

From Cisco Switches came with this IOS Image cat4500e-universal.SPA.03.04.00.SG.151-2.SG.bin

Later i upgraded the switch with this ios image cat4500e-universalk9.SPA.03.05.01.E.152-1.E1.bin

Still the full funtionality of EIGRP is not supported but SSH worked on both switches which confirms image is upgraded properly. I read on cisco release notes that switch must have enterprise licence to support full EIGRP. Please advise how can i achieve it.

Kindly find the show verson output when the switch received from cisco before upgrading the image.

sh version

Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.04.00.SG RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Wed 05-Dec-12 05:58 by prod_rel_team

Cisco IOS-XE software, Copyright (c) 2005-2010, 2012 by cisco Systems, Inc.

All rights reserved.  Certain components of Cisco IOS-XE software are

licensed under the GNU General Public License ("GPL") Version 2.0.  The

software code licensed under GPL Version 2.0 is free software that comes

with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such

GPL code under the terms of GPL Version 2.0.  For more details, see the

documentation or "License Notice" file accompanying the IOS-XE software,

or the applicable URL provided on the flyer accompanying the IOS-XE

software.

ROM: 15.0(1r)SG5

DC-CORE-SW1 uptime is 2 weeks, 2 days, 23 hours, 23 minutes

System returned to ROM by power-on

System restarted at 02:54:46 

Running default software

Jawa Revision 7, Snowtrooper Revision 0x0.0x1C

Last reload reason: power-on

License Information for 'WS-X45-SUP7-E'

    License Level: ipbase   Type: Permanent

    Next reboot license Level: ipbase

cisco WS-C4506-E (MPC8572) processor (revision 10) with 2097152K/20480K bytes of memory.

Processor board ID FXS1724Q233

MPC8572 CPU at 1.5GHz, Supervisor 7

Last reset from PowerUp

36 Virtual Ethernet interfaces

72 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

6 Replies 6

daniel.dib
Level 7
Level 7

You need to activate enterprise services license. Here is link how to do it:

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/XE3.5.0E/15.21E/configuration/guide/swadmin.html#wp1347232

Here are also some useful links:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/qa_c67-621718.html

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/at_a_glance_c45-619755.pdf

It seems that you don't have to type in the license any longer which is mutual trust from Cisco that you already got the correct license but it is not enforced.

Daniel Dib
CCIE #37149

Please rate helpful posts.

Daniel Dib
CCIE #37149
CCDE #20160011

Please rate helpful posts.

Thanks for the reply Daniel

As per your post device already has the licence and it just need enforcement. If i use this command ("license right-to-use activate feature-name") then EIGRP full feature should work.

Am i correct ?

Yes, that's what I figure from the configuration guide. There seems to be a command to set the license level on boot, so have a look at that as well. Wouldn't be nice to have it boot up on IP Base and EIGRP not coming up.

Daniel Dib
CCIE #37149

Please rate helpful posts.

Daniel Dib
CCIE #37149
CCDE #20160011

Please rate helpful posts.

Hi Daniel,

Find below show license all and show version output and i removed the eigrp stub command. its shows that licence is permenent and in use for entservices

sh license all

License Store: Primary License Storage

StoreIndex: 0 Feature: ipbase  Version: 1.0

      License Type: Permanent

      License State: Active, Not in Use

      License Count: Non-Counted

      License Priority: Medium

License Store: Dynamic License Storage

License Store: Primary License Storage

License Store: Dynamic License Storage

StoreIndex: 0 Feature: entservices  Version: 1.0

      License Type: Evaluation

        Evaluation total period: 8 weeks 4 days

        Evaluation period left: 8 weeks 4 days

      License State: Inactive

      License Count: Non-Counted

      License Priority: None

StoreIndex: 1 Feature: entservices  Version: 1.0

      License Type: PermanentRightToUse

      License State: Active, In Use

      License Count: Non-Counted

StoreIndex: 2 Feature: ipbase  Version: 1.0

      License Type: Evaluation

        Evaluation total period: 8 weeks 4 days

        Evaluation period left: 8 weeks 4 days

      License State: Inactive

      License Count: Non-Counted

      License Priority: None

StoreIndex: 3 Feature: ipbase  Version: 1.0

      License Type: PermanentRightToUse

      License State: Inactive

      License Count: Non-Counted

sh version

Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.05.01.E RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Sat 23-Nov-13 00:13 by prod_rel_team

ROM: 15.0(1r)SG5

CORE-SW2 uptime is 11 minutes

System returned to ROM by reload

System restarted at 03:04:39 Wed Jan 1 2014

Running default software

Jawa Revision 7, Snowtrooper Revision 0x0.0x1C

Last reload reason: Reload command

License Information for 'WS-X45-SUP7-E'

License Level: entservices   Type: Permanent Right-To-Use

Next reboot license Level: entservices

cisco WS-C4506-E (MPC8572) processor (revision 10) with 2097152K bytes of physical memory.

Processor board ID FXS1724Q22W

MPC8572 CPU at 1.5GHz, Supervisor 7

Last reset from Reload

51 Virtual Ethernet interfaces

72 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

Hope its solved the problem and actived the licence entservices form ip base.

I use the following commands.

license right-to-use activate entservices 

accept the EULA

conf t

license boot level entservices

wr mem

reload.

verified by using commands

show licence all

show version

removed eigrp stub command which was restricted in ipbase license.

Thanks for your support..

That looks good.

Glad you got it solved. Happy new year!

Daniel Dib
CCIE #37149

Please rate helpful posts.

Daniel Dib
CCIE #37149
CCDE #20160011

Please rate helpful posts.

Hi

 

Finding difficulty in running EIGRP in 

cisco WS-C4506-E (P5040) processor (revision 2) with 4194304K bytes of physical memory.

With SUP 8 

System image file is "bootflash:cat4500es8-universalk9.SPA.03.03.01.XO.151-1.XO1.bin"
 

Im not even seeiing the command router EIGRP in help

Review Cisco Networking for a $25 gift card