I was trying to configure routeron stick.
1) I configured sub interfaces on Router and assign IP address
1) I configured switch 1 as VTP server and made 3 uplink ports as Trunk , also created 4 Vlans
Problem : Vlans are showing on Switch 1 only not on Switch 2,3 and 4
while those are configured as Clients.
So, please help me where I am missing
Configuration are as below
---------------------
Router
Router# sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES unset up up
FastEthernet0/0.1 192.168.1.1 YES manual up up
FastEthernet0/0.2 192.168.2.1 YES manual up up
FastEthernet0/0.3 192.168.3.1 YES manual up up
FastEthernet0/0.4 192.168.4.1 YES manual up up
interface FastEthernet0/0
no ip address
duplex auto
speed auto
!
interface FastEthernet0/0.1
description DATA
encapsulation dot1Q 100
ip address 192.168.1.1 255.255.255.0
!
interface FastEthernet0/0.2
description WIRELESS
encapsulation dot1Q 200
ip address 192.168.2.1 255.255.255.0
!
interface FastEthernet0/0.3
description VOICE
encapsulation dot1Q 300
ip address 192.168.3.1 255.255.255.0
!
interface FastEthernet0/0.4
description CLIENTS
encapsulation dot1Q 400
ip address 192.168.4.1 255.255.255.0
===========================================================
Switch#1
Vlan1 10.10.20.1 YES manual up up
Vlan100 192.168.1.2 YES manual up up
Vlan200 192.168.2.2 YES manual up up
Vlan300 192.168.3.2 YES manual up up
Vlan400 192.168.4.2 YES manual up up
Switch_1:core#sh int trunk
Port Mode Encapsulation Status Native vlan
Fa0/2 on 802.1q trunking 1
Fa0/3 on 802.1q trunking 1
Fa0/4 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/2 1-1005
Fa0/3 1-1005
Fa0/4 1-1005
Port Vlans allowed and active in management domain
Fa0/2 1,100,200,300,400
Fa0/3 1,100,200,300,400
Fa0/4 1,100,200,300,400
Port Vlans in spanning tree forwarding state and not pruned
Fa0/2 1,100,200,300,400
Fa0/3 1,100,200,300,400
Fa0/4 1,100,200,300,400
Switch_1:core#
Switch_1:core#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig0/1, Gig0/2
100 Data active
200 Wireless active
300 Voice active
400 Clients active
Switch_1:core# sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 255
Number of existing VLANs : 9
VTP Operating Mode : Server
VTP Domain Name : Cisco
=========================================================
Switch:2#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/11, Fa0/16, Fa0/17, Fa0/23
Fa0/24, Gig0/1, Gig0/2
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Switch:2# sh int trunk
Port Mode Encapsulation Status Native vlan
Fa0/1 on 802.1q trunking 1
Switch:2#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 255
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : Cisco
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
