cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
215
Views
0
Helpful
3
Replies

SPAN by destanation port-channel

Hi I have 3064 Source interface port-channel 6

Now I set destanation port-channel 8

IF set on the port for example channel-group 8 force mode active

Donnot have command switchport monitor

On the port-channel interface also donnot have command switchport-monitor

now if set dest port on interface port-channel 8 monitor sesssion donnot up say to me dst port in wrong mode

 

show version of switch


Software
BIOS: version 5.0.0
NXOS: version 9.3(10)
BIOS compile time: 06/05/2018
NXOS image file is: bootflash:///nxos.9.3.10.bin
NXOS compile time: 7/8/2022 9:00:00 [07/08/2022 18:10:17]


Hardware
cisco Nexus3000 C3064PQ Chassis
Intel(R) Celeron(R) CPU P4505 @ 1.87GHz with 3901496 kB of memory.
Processor Board ID FOC17366Z65

Device name: Switch-3064-L2-Transit
bootflash: 1874880 kB
usb1: 0 kB (expansion flash)

Kernel uptime is 26 day(s), 16 hour(s), 57 minute(s), 15 second(s)

Last reset at 806005 usecs after Sat Jan 30 13:21:51 2010
Reason: Reset Requested by CLI command reload
System version: 9.3(10)
Service:

plugin
Core Plugin, Ethernet Plugin

Active Package(s):

 

How can solve this ??

 

1 Accepted Solution

Accepted Solutions

have you got chance to read the post replied above and limitation.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

3 Replies 3

balaji.bandi
Hall of Fame
Hall of Fame

Why do you want destination as Port-channel ? what is the use case. And it is  not supported.

Characteristics of Destination Ports

Each local SPAN session must have a destination port (also called a monitoring port) that receives a copy of traffic from the source ports or VLANs. A destination port has these characteristics:

  • Can be any physical port. Source Ethernet and FCoE ports cannot be destination ports.

  • Cannot be a source port.

  • Cannot be a port channel.

  • Does not participate in spanning tree while the SPAN session is active.

  • Is excluded from the source list and is not monitored if it belongs to a source VLAN of any SPAN session.

  • Receives copies of sent and received traffic for all monitored source ports.

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus3000/sw/system_mgmt/7_x/b_Cisco_Nexus_3000_Series_NX-OS_System_Management_Configuration_Guide_7x/b_Cisco_Nexus_3000_Series_NX-OS_System_Management_Configuration_Guide_7x_chapter_010001.ht...

 

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Sure Can you tess on nexus 3064 source port port-channel 1

destanation port port-channel2

If you config port-channel For LACP or other mode

For example ethernet 1/1

channel-group 1 force mode active

and ethernet 1/2

channel-group 1 force mode active

You want copy taffic port-channle 1 to port-channel 2

have not command swtich port monitor on port-channel config

have you got chance to read the post replied above and limitation.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Review Cisco Networking for a $25 gift card