Hello
I will be replacing our current single chassis (WS-C6509) with the (WS-C6509-E) chassis. What I want to do is just take our line cards from our current chassis below and place them in our new chassis. Considering we are moving the Supervisors also, do I need to make sure of anything as far as configuration? The swap just seems to straight forward but maybe I'm looking too into this. I've backed up the IOS, configs that include the ACLS since we use it as our firewall. After I moved over the line cards and powered up I was only going to connect our Supervisors which connect to our ISP to verify route connectivity then for the most part everything else are trunks going to our switches.
I'm curious if their are any gotchas or things I should be prepared for whether it be hardware or configs. Any tips would be greatly appreciated.
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
3 24 24 port 100FX Multi mode WS-X6324-100FX-MM
5 2 Supervisor Engine 720 (Hot) WS-SUP720-3B
6 2 Supervisor Engine 720 (Active) WS-SUP720-3B
8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX
9 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX
Mod Sub-Module Model Hw Status
---- --------------------------- ------------------ ------- -------
2 Centralized Forwarding Card WS-F6700-CFC 4.1 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 3.1 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B 2.5 Ok
6 MSFC3 Daughterboard WS-SUP720 3.5 Ok
8 Centralized Forwarding Card WS-F6700-CFC 4.1 Ok
9 Centralized Forwarding Card WS-F6700-CFC 4.0 Ok
system power redundancy mode = redundant
system power total = 2771.16 Watts (65.98 Amps @ 42V)
system power used = 1404.48 Watts (33.44 Amps @ 42V)
system power available = 1366.68 Watts (32.54 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-3000W 2771.16 65.98 OK OK on
2 WS-CAC-3000W 2771.16 65.98 OK OK on
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on
3 WS-X6324-100FX-MM 63.84 1.52 63.84 1.52 on on
5 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
6 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
8 WS-X6748-GE-TX 325.50 7.75 325.50 7.75 on on
9 WS-X6748-GE-TX 325.50 7.75 325.50 7.75 on on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 3780.00 Watts (90.00 Amps @ 42V)
system auxiliary connector power limit = 0 Watt
system primary power used = 1404.48 Watts (33.44 Amps @ 42V)
system auxiliary power used = 0 Watt
