Hi All,
Anyone face the same problem with the following IOS Version?
MLS QOS is not supported in global command.
Switch#sh ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 14-Aug-13 07:26 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: 15.1(1r)SG2
Switch uptime is 6 minutes
System returned to ROM by power-on
Running default software
Jawa Revision 3, RadTrooper Revision 0x0.0x41, Conan Revision 0x1449
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
License Information for 'WS-X45-SUP8-E'
License Level: entservices Type: Permanent
Next reboot license Level: entservices
cisco WS-C4506-E (P5040) processor (revision 2) with 4194304K bytes of physical memory.
Processor board ID FXS1812Q346
P5040 CPU at 2.2GHz, Supervisor 8-E
Last reset from PowerUp
1 Virtual Ethernet interface
20 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
SWITCH(config)#mls qos
^
% Invalid input detected at '^' marker.
SWITCH(config)#
SWITCH(config)#?
Configure commands:
aaa Authentication, Authorization and Accounting.
access-list Add an access list entry
access-session Access Sesion Global Configuration Commands
agent-server Modify DNS server properties
alias Create command alias
ancp Configure ANCP
archive Archive the configuration
arp Set a static ARP entry
async-bootp Modify system bootp parameters
audit Router Audit
authentication Auth Manager Global Configuration Commands
auto Configure Automation
banner Define a login banner
beep Configure BEEP (Blocks Extensible Exchange
Protocol)
bfd BFD configuration commands
bfd-template BFD template configuration
boot Modify system boot parameters
bridge Bridge Group.
buffers Adjust system buffer pool parameters
bulkstat Bulkstat Application
call-home Enter call-home configuration mode
cdp Global CDP configuration subcommands
cef Cisco Express Forwarding
cisp Set CISP parameters
class-map Configure CPL Class Map
clns Global CLNS configuration subcommands
clock Configure time-of-day clock
cluster Cluster configuration commands
cns CNS agents
comet-server Configure comet-server properties
config-register Define the configuration register
configuration Configuration access
control-plane Configure control plane services
crypto Encryption module
cts Cisco Trusted Security commands
default Set a command to its defaults
default-value Default character-bits values
define interface range macro definition
device-sensor IOS Sensor Commands
diagnostic Configure diagnostic information
dns-server Modify DNS server properties
dnsix-dmdp Provide DMDP service for DNSIX
dnsix-nat Provide DNSIX service for audit trails
do-exec To run exec commands in config mode
dot1x IEEE 802.1X Global Configuration Commands
downward-compatible-config Generate a configuration compatible with older
software
eap EAP Global Configuration Commands
emm Specify pre-loading of MDF
enable Modify enable password parameters
end Exit from configure mode
energywise EnergyWise Global Configuration Commands
epm EPM Global Configuration Commands
errdisable Error disable
ethernet Ethernet configuration
event Event related configuration commands
exception Exception handling
exit Exit from configure mode
fallback Fallback configuration commands
fhrp Configure First Hop Redundancy Protocols
file Adjust file system parameters
fips FIPS mode after next reload
flow Global Flow configuration subcommands
format Format the output
global-address-family Enter address-family base routing topology mode
help Description of the interactive help system
hostname Set system's network name
hw-module Apply command (e.g. shutdown) to specified
hardware target
hw-module Control of individual components in the system
hw-switch Control of individual components in the switch
id-manager ID Pool Manager
identity Identity Configuration Commands
infra-test Configure end2end properties
interface Select an interface to configure
ip Global IP configuration subcommands
ipc Configure IPC system
ipv6 Global IPv6 configuration commands
isis Global ISIS configuration subcommands
issu no description
key Key management
kron Kron interval Facility
l2 Layer 2
l2protocol-tunnel Tunnel Layer2 protocols
lacp LACP configuration
li-view LI View
license Configure License
line Configure a terminal line
link Enable Link State Tracking feature
lldp Global LLDP configuration subcommands
location Global location configuration commands
logging Modify message logging facilities
login Enable secure login checking
mab MAC Authentication Bypass Global Configuration
Commands
mac Global MAC configuration subcommands
macro Macro configuration
media-proxy Global media proxy configuration
mediatrace Mediatrace Application
memory Configure memory management
metadata Metadata Application
mka MACsec Key Agreement (MKA) configuration
module Module
monitor Monitoring different system events
mvr Enable/Disable MVR on the switch
netconf Configure NETCONF
Thank you.
