cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2219
Views
0
Helpful
12
Replies

Web GUI and CLI unavailable/not working

Ikon1
Level 1
Level 1

I have an cisco 300sf-24pp network switch and I am unable to access the web GUI or the CLI.

The switch is working with 100 up and 100 down.

Iv'e tried factory reseting it but same issue

1 Accepted Solution

Accepted Solutions

balaji.bandi
Hall of Fame
Hall of Fame

Turn off the device wait for 10min, and do the factory reset :

 

https://www.cisco.com/c/en/us/support/docs/smb/switches/cisco-350-series-managed-switches/smb985-how-to-manually-reboot-or-reset-a-switch.html

 

The switch is working with 100 up and 100 down.

not sure if we understand this, what is 100 up and 100 down mean?

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

12 Replies 12

marce1000
VIP
VIP

 

         - What address did you try (e.g.) ? What happens when you try to use  the  GUI or CLI ?

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

When I try to use the web GUI it loads for some time then it says no connection. When I try to use the CLI it is just blank, and I have the right CLI settings and I use putty. After I have factory reseted, I try to use 192.168.1.254 but it's not working

balaji.bandi
Hall of Fame
Hall of Fame

Turn off the device wait for 10min, and do the factory reset :

 

https://www.cisco.com/c/en/us/support/docs/smb/switches/cisco-350-series-managed-switches/smb985-how-to-manually-reboot-or-reset-a-switch.html

 

The switch is working with 100 up and 100 down.

not sure if we understand this, what is 100 up and 100 down mean?

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Im gonna try that.

 

What I mean with 100 up and down is 100mbps up/upload and 100mbps down/download through the ethernet ports

as per the model its only 100MB, so you are good in terms of connection.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Tanks. Your solution worked. But is there some way i can make it go from 100 to 500mbps?

The switch is 100MB as per the specification, so check you can use uplinks they are 1GB

 

image.png

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

I don't exactly know how to do that, so if you could send me a tutorial, that would be great.

 

Do you know anything about igmp proxy? And how to turn it on?

Check-in Front of the switch there are 2 ports Modular, you need to buy GLC-T 1G Ethernet to work for 1GB network.

 

IGMP Proxy, I am not sure these models support, since these are SMB switches.

 

for IGMP look at the admin guide :

 

https://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Would this: Fiberworks 1G SFP 1000Base-LX LC Duplex. Work?

 

https://www.finn.no/179234651

 

                     - Correct operational  use of none-cisco (foreign) SFP's can not be guaranteed : https://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/Cisco_300Sx_v1_4_AG.pdf , start reading from Displaying Optical Module Status

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

YES and NO. I would advise using Cisco SFP (even it is refurbished) for easy installation and working conditions.

 

Note: some devices in cisco do not accept 3rd party SFP.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: