11-09-2019 12:06 AM
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.11.08 08:46:34 =~=~=~=~=~=~=~=~=~=~=~=
login as:
Using keyboard-interactive authentication.
password:
TEST#show ver
....
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 54 WS-C2960X-48TS-L 15.2(7)E0a C2960X-UNIVERSALK9-M
.....
TEST#terminal mon
TEST#show running-config interface gi1/0/1
Building configuration...
Current configuration : 1099 bytes
!
interface GigabitEthernet1/0/1
switchport access vlan 999
switchport mode access
switchport nonegotiate
switchport voice vlan 800
end
TEST#show mac address-table interface gi1/0/1
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TEST#terminal mon
TEST#
Nov 8 03:48:09.724: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up
Nov 8 03:48:10.731: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
TEST#
Nov 8 03:48:58.156: %SWITCH_QOS_TB-5-TRUST_DEVICE_DETECTED: cisco-phone detected on port Gi1/0/1, port's configured trust state is now operational.
TEST# show mac address-table interface gi1/0/1
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
800 001a.2f69.dbbb DYNAMIC Gi1/0/1
999 001a.2f69.dbbb DYNAMIC Gi1/0/1
Total Mac Addresses for this criterion: 2
Nov 8 03:52:26.907: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Nov 8 03:52:27.907: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
TEST#
Nov 8 03:52:29.557: %SWITCH_QOS_TB-5-TRUST_DEVICE_LOST: cisco-phone no longer detected on port Gi1/0/1, operational port trust state is now untrusted.
TEST#show mac address-table interface gi1/0/1
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TEST#
Nov 8 03:53:04.347: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up
TEST#
Nov 8 03:53:05.350: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
TEST#show mac address-table interface gi1/0/1
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
999 0021.5a62.5ac0 DYNAMIC Gi1/0/1
999 00a2.89e5.df01 DYNAMIC Gi1/0/1
999 2c41.389c.d1f8 DYNAMIC Gi1/0/1
999 5065.f340.1a2f DYNAMIC Gi1/0/1
999 705a.0f4e.0868 DYNAMIC Gi1/0/1
999 7c0e.ce02.e000 DYNAMIC Gi1/0/1
999 c434.6b5c.89c2 DYNAMIC Gi1/0/1
999 c434.6b70.7d16 DYNAMIC Gi1/0/1
Total Mac Addresses for this criterion: 8
TEST# show mac address-table interface gi1/0/1
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
999 0021.5a62.5ac0 DYNAMIC Gi1/0/1
999 00a2.89e5.df01 DYNAMIC Gi1/0/1
999 2c41.389c.d1f8 DYNAMIC Gi1/0/1
999 5065.f340.1a2f DYNAMIC Gi1/0/1
999 705a.0f4e.0868 DYNAMIC Gi1/0/1
999 78ac.c0ab.2466 DYNAMIC Gi1/0/1
999 7c0e.ce02.e000 DYNAMIC Gi1/0/1
999 c434.6b5c.89c2 DYNAMIC Gi1/0/1
999 c434.6b70.7d16 DYNAMIC Gi1/0/1
Total Mac Addresses for this criterion: 9
TEST#
Nov 8 03:53:38.721: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Nov 8 03:53:39.720: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
TEST#
Nov 8 03:53:38.721: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down <- it is me - removed lan cable from phone
if the port configuration is clear (null) - we have the same situatuin
Solved! Go to Solution.
11-10-2019 02:43 PM
Hi,
You may be hitting the CSCuz92903 bug. Can you please try to configure either "no keepalive" or "speed auto 100 1000" under the interface where the phone is connected and see if there is any difference.
Best regards,
Antonin
11-09-2019 12:10 AM
11-09-2019 12:21 AM
no!
After power off ip phone - port is going down and after 30 second port is going up and on the port the status is connected until it is either disabled by command shutdown or physically turned off.
Yes - LLDP and CDP we turn off/on - problame the same
11-09-2019 01:45 AM
11-09-2019 02:53 AM
11-10-2019 02:43 PM
Hi,
You may be hitting the CSCuz92903 bug. Can you please try to configure either "no keepalive" or "speed auto 100 1000" under the interface where the phone is connected and see if there is any difference.
Best regards,
Antonin
11-10-2019 08:05 PM
yes, it is solved our problame.
But it is intresting - bug date 2016/2017 year.
we have latest firmware flash:c2960x-universalk9-mz.152-7.E0a.bin", and we have the same problame...
11-10-2019 09:18 PM
it is not the end....
i try to write this command on all of switch that i have with this problame.
after some time mac on the port that work "OK" disappeared.... and we have another problame :(
11-11-2019 10:04 AM
Hi,
Thanks for the feedback. In my view you should first replace your IOS version. The commands are meant as a workaround only not the final solution. Out of these two I would return keepalives back and stay with the "speed auto 100 1000" only. At the moment I have only Cat2960Xs with PoE in my lab and these are not prone to this bug so I cannot test the suitable IOS version for you. Provided you are entitled to raise TAC cases you should go that way if not will you please contact your Cisco supplier.
Best regards,
Antonin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide