API command for Log Output

[Mahesh Kumar]

What is command to see the live log output using SSH api command via root, please find the below example.

2016.77 VIDEOLC-0 I: VLC_readySignalSourceEvent port:HDMI 1: no signal
2016.78 VIDEOLC-0 I: Received SourceFormatEvent from video link 16 (0x0@0, unknown type, error detected) in ready state
2016.78 MC I: LocalVideoInputGateImpl::setIncomingModeReport(ig=1,p=1)  [Video (0): vid-off 0x0@0.0  0k ]
2016.78 MC I: LocalVideoInputGateImpl::recalcIncomingMode(ig=1) res=0x0@0 q=Motion t60=921600 p=Normal
2016.78 MC I: LocalVideoInputGateImpl::recalcIncomingMode(ig=1) res=0x0@0 q=Motion t60=921600 p=Normal
2016.79 MC I: LocalVideoInputGateImpl::recalcIncomingMode(ig=1) res=0x0@0 q=Motion t60=921600 p=Normal
2016.79 MC I: LocalVideoInputGateImpl::recalcIncomingMode(ig=1) res=0x0@0 q=Motion t60=921600 p=Normal
2016.79 MC I: LocalVideoInputGateImpl::recalcIncomingMode(ig=1) res=0x0@0 q=Motion t60=921600 p=Normal
2017.09 MediaStreamController I: MV::getVCSetting getOutputPortStatus initialized 1

2017.09 MediaStreamController I: MV::getVCSetting localHwCookieHint_ 16 w 720 h 480

2017.09 MediaStreamController I: MV::getVCSetting getOutputPortStatus initialized 1

2017.09 MediaStreamController I: MV::getVCSetting localHwCookieHint_ 0 w 1280 h 720

2017.09 MediaStreamController I: MV::getVCSetting getOutputPortStatus initialized 1

2017.10 MediaStreamController I: MV::getVCSetting localHwCookieHint_ 8 w 1024 h 768

2040.06 VIDEOLC-0 I: VLC_readySignalSourceEvent port:HDMI 1: have signal

Thanks in Advance

Mahesh Kumar                  

[Dharmesh Nandoria · Accepted solution]

Hi Mahesh,

use commnad : "log output on" from admin login .

Kind regards,

Dharmmesh

[Mahesh Kumar]

Dear Dharmesh,

          Really appreciate your quick response and for what echo ON and OFF command used in this scenario, does this makes any changes.

Sincerely,

Mahesh Kumar

[Martin Koch]

What do you refer to as "echo"?

The log command parameters (TC6) work like this:

log output
Unknown command or wrong number of arguments
usage: log COMMAND [PARAMETER]...
 Commands to control message production:
  ctx [CTX]+ debug N          Enable debug level N (1..9) for the context CTX
 Other commands:
  list                    Lists registered contexts
  output          Output log to this console.
  help                    This help text
 Parameter:
  LEVEL  - |info|notice|warning|error>
  CTX    - context name (as can be seen from "log list")

a reboot should also stop the logging

[Martin Koch]

These two documents might be also interesting for you:

https://supportforums.cisco.com/docs/DOC-29766

https://supportforums.cisco.com/docs/DOC-15643

[Mahesh Kumar]

Hi Dharmesh,

          How to get only video or audio log output, because now if i say "log output on" it shows all the logs but if i want only any particular log. e.g. video, audio or network.

Sincerely,

Mahesh Kumar

[Dharmesh Nandoria]

Hi Mahesh,

If you want to look audio / video protocol, statistic, packet loss  for call ,use xstatus  It will have all detail.

Live log out put will provide detail for all logs , If you want to look specific log then log in from web interface  go to current log and down load specific log .

hth

Kind regards,

Dharmmesh