02-23-2018 03:49 AM - edited 03-19-2019 01:10 PM
We have configured SRST at Remote branch.
Please find configuration.
Please let me know if is there any changes in this configuration.
I have one question should i create dial-peer for incoming call.
call-manager-fallback
max-conferences 8 gain -6
transfer-system full-consult
ip source-address 10.108.20.6 port 2000
max-ephones 50
max-dn 50
system message primary SRST Active
keepalive 20
ccm-manager fallback-mgcp
application
global
service alternate default
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
bind control source-interface GigabitEthernet0/0/0
bind media source-interface GigabitEthernet0/0/0
registrar server expires max 1200 min 60
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice register global
esrst
timeouts interdigit 5
system message "SRST Mode"
max-dn 50
max-pool 50
voice register pool 1
id network 10.108.22.0 mask 255.255.255.0
no digit collect kpml
voice-class codec 1
voice translation-rule 1
rule 1 /^62726\(6..\)$/ /6\1/
!
voice translation-rule 2
rule 1 /^62726\(5..\)$/ /6\1/
!
!
voice translation-profile SRST1
translate called 1
!
voice translation-profile SRST2
translate called 2
!
voice-port 0/1/0:15
translation-profile incoming SRST1
!
voice-port 0/1/1:15
translation-profile incoming SRST2
!
DID range =627266XX
dial-peer voice 11 pots
description "SRST_LOCAL_MOB_CALLS"
incoming called-number 66..
destination-pattern 9[7-9].........
port 0/1/0:15
forward-digits 10
!
dial-peer voice 12 pots
description "SRST_LOCALCAllS"
incoming called-number 66..
destination-pattern 9[1-7].......
port 0/1/0:15
forward-digits 8
!
dial-peer voice 13 pots
description "SRST_STDCALLS"
incoming called-number 66..
destination-pattern 90[0-9].........
port 0/1/0:15
forward-digits 11
!
dial-peer voice 14 pots
description "SRST_ISDCALL"
incoming called-number 66..
destination-pattern 900T
port 0/1/0:15
prefix 00
DID range =627265XX
dial-peer voice 1 pots
description "SRST_LOCAL_MOB_CALLS"
incoming called-number 65..
destination-pattern 9[7-9].........
port 0/1/1:15
forward-digits 10
!
dial-peer voice 2 pots
description "SRST_LOCALCAllS"
incoming called-number 65..
destination-pattern 9[1-7].......
port 0/1/1:15
forward-digits 8
!
dial-peer voice 3 pots
description "SRST_STDCALLS"
incoming called-number 65..
destination-pattern 90[0-9].........
port 0/1/1:15
forward-digits 11
!
dial-peer voice 4 pots
description "SRST_ISDCALL"
incoming called-number 65..
destination-pattern 900T
port 0/1/0:15
prefix 00
Solved! Go to Solution.
02-26-2018 01:34 PM
Hi,
use de following debug and send the log please:
debug voice ccapi inout
Best regards,
Marcelo Morais
02-24-2018 02:08 PM
Hi,
the incoming called-number command is one of the responsible for the dial-peer incoming calls, to make the dial-peer more clear you can remove all the incoming called-number commands and insert the following lines:
dial-peer voice 66 pots
description "SRST_INCOMING_FROM_PSTN 0/1/0"
incoming called-number 66..
direct-inward-dial
port 0/1/0:15
dial-peer voice 65 pots
description "SRST_INCOMING_FROM_PSTN 0/1/1"
incoming called-number 65..
direct-inward-dial
port 0/1/1:15
Hope this helps,
Marcelo Morais
02-25-2018 07:52 PM
Hi Marcelo,
I have configured this but getting issue
Cause i = 0x8292 - No user responding
02-26-2018 01:34 PM
Hi,
use de following debug and send the log please:
debug voice ccapi inout
Best regards,
Marcelo Morais
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide