Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
4531
Views
0
Helpful
5
Replies

F0637 Power Cap Fault

Dan Laden
Level 1
Level 1

‎06-21-2018 04:10 PM - edited ‎03-01-2019 01:35 PM

Running UCS 3.2.2f with B480M5s with same firmware.  I have a Power Control policy to impose "No-Cap" Power Control.  Each server where it is applied, i get the F0637 fault.  If I remove the policy, the fault clears.  I had seen  a bug in 3.1 but resolved in same.  CSCvc02297.  I had trying the work-around of power down via the OS and boot via UCSM.  This did not clear the fault.

 

Anyone seen this elsewhere?

 

Thank you for any insight,

Dan Laden

0 Helpful
5 Replies 5

Kirk J
Cisco Employee
Cisco Employee

‎06-21-2018 07:08 PM - edited ‎06-22-2018 03:19 AM

Greetings.

Trying pulling some power related settings from the cli:

#scope chassis x

#scope server y

#show power-budget expand detail

 

#scope chassis x

#show power-budget detail

 

exit out to top level of ucsm cli

#connect iom x (where x is chassis with blade in question)

#show platform software cmcctrl power config

#show platform software cmcctrl dmclient psreadings  (if output is all zeros, then connect to other IOM in same chassis

You may want to try re-acking server if you haven't already...

 

Thanks,

Kirk...

0 Helpful

Dan Laden
Level 1
Level 1
In response to Kirk J

‎06-22-2018 08:15 AM

 

 

ucs-A /chassis/server # show power-budget expand detail

Budget:
AdminCommitted (W): 0

 

ucs-A /chassis # show power-budget detail

Budget:
Device Id: blade 1/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 301
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 1/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 322
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 1/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 289
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 1/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 288
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: chassis 1
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 756
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No

Device Id: blade 2/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 10
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Unbudgeted
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 2/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 279
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 2/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 310
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 2/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 320
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: chassis 2
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 726
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No

Device Id: blade 3/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 316
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 3/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 287
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 3/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 280
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: blade 3/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 293
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes

Device Id: chassis 3
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 724
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No

Device Id: switch A
Power Cap (W): 335
Applied Power Cap (W): 335
Admin Priority: No Cap
Maximum power (W): 335
Minimum power (W): 335
Group: default
Average Usage (W): 335
Power Profiling: No
Method: Static
OperMethod: Static
OperState: Deployed
Psu State: Ok
Power Cap Support: No

Device Id: switch B
Power Cap (W): 335
Applied Power Cap (W): 335
Admin Priority: No Cap
Maximum power (W): 335
Minimum power (W): 335
Group: default
Average Usage (W): 335
Power Profiling: No
Method: Static
OperMethod: Static
OperState: Deployed
Psu State: Ok
Power Cap Support: No
ucs-A /chassis #
ucs- A# connect iom 1
Attaching to FEX 1 ...
To exit type 'exit', to abort type '$.'
Bad terminal type: "dumb". Will assume vt100.
fex-1# show platform software cmcctrl power config
Redundancy policy: Grid
Chassis power budget: 720/800 # committed/peak
Chassis settings:
pwrcap enabled
dynamic rebalancing enabled
Blade 0:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 1:
Presence: ABSENT
Blade 2:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 3:
Presence: ABSENT
Blade 4:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 5:
Presence: ABSENT
Blade 6:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 7:
Presence: ABSENT
fex-1#

fex-1# show platform software cmcctrl dmclient psreadings
Total Input Power consumption: -1
Total Output Power consumption: -1
Power supply: 0
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : N/A
Fan tach1 : N/A
Fan tach2 : N/A
Fan tach3 : N/A
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 1
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 2
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : N/A
Fan tach1 : N/A
Fan tach2 : N/A
Fan tach3 : N/A
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 3
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
fex-1#

ucs-B# connect iom 1
Attaching to FEX 1 ...
To exit type 'exit', to abort type '$.'
Bad terminal type: "dumb". Will assume vt100.
fex-1#
fex-1#
fex-1# show platform software cmcctrl power config
Redundancy policy: Grid
Chassis power budget: 720/800 # committed/peak
Chassis settings:
pwrcap enabled
dynamic rebalancing enabled
Blade 0:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 1:
Presence: ABSENT
Blade 2:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 3:
Presence: ABSENT
Blade 4:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 5:
Presence: ABSENT
Blade 6:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 7:
Presence: ABSENT
fex-1# show platform software cmcctrl dmclient psreadings
Total Input Power consumption: 2322
Total Output Power consumption: 2188
Power supply: 0
Voltage (IN) : 234 V
Voltage (12V) : 12082 mV
Voltage (3V) : 3367 mV
Current (IN) : 4984 mA
Current (12V) : 90250 mA
Current (3V) : 15 mA
Peak Current (IN) : 5140 mA
Peak Current (12V) : 92718 mA
Peak Current (3V) : 31 mA
Temperature 0 : 26 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 5520 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x30
Operating range : First
Max Power : 2500 W
Power supply: 1
Voltage (IN) : 236 V
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : 24 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x1
Operating range : First
Max Power : 2500 W
Power supply: 2
Voltage (IN) : 232 V
Voltage (12V) : 12070 mV
Voltage (3V) : 3363 mV
Current (IN) : 4984 mA
Current (12V) : 90968 mA
Current (3V) : 0 mA
Peak Current (IN) : 5140 mA
Peak Current (12V) : 93984 mA
Peak Current (3V) : 0 mA
Temperature 0 : 25 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 5790 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x30
Operating range : First
Max Power : 2500 W
Power supply: 3
Voltage (IN) : 238 V
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : 25 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x1
Operating range : First
Max Power : 2500 W
fex-1#

 

 

Thank You,

Dan Laden

 

 

0 Helpful

Dan Laden
Level 1
Level 1
In response to Dan Laden

‎06-29-2018 09:02 AM

I have not be able to re-ack the blade.  How likely is it to resolve the issue?

0 Helpful

Tapper
Level 1
Level 1
In response to Dan Laden

‎10-16-2019 08:08 AM

I have this issue with only M4 blades.  The re-acknowledge is the only thing that seems to clear out the error.

0 Helpful

flynmooney
Level 1
Level 1

‎09-10-2018 12:03 PM

Seeing this after trying out VMware DPM which uses IPMI to shutdown and start up blades.  Running 3.2.2f with B200M4 & M5.

0 Helpful
Customers Also Viewed These Support Documents

Review Cisco Networking for a $25 gift card