- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 09:49 AM - edited 03-01-2019 11:49 AM
I would like to know why i got error disabled, I guess there were link flap, am i correct ?
How Can I recover this interface from error disabled,
Solved! Go to Solution.
- Labels:
-
Unified Computing System (UCS)
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 11:39 PM
Make sure the blade is up and you have a OS installed. If you don't an OS installed or the blade is powered off you might see these errors.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 10:31 AM
some outputs
FABRIC-001-A(nxos)#(nxos)# show interface vethernet 930
Vethernet930 is down (nonParticipating)
Bound Interface is --
Port description is server 1/5, VNIC vNIC0
Hardware is Virtual, address is 002a.6a81.77a0
Port mode is trunk
Speed is auto-speed
Duplex mode is auto
300 seconds input rate 0 bits/sec, 0 packets/sec
300 seconds output rate 0 bits/sec, 0 packets/sec
Rx
0 unicast packets 0 multicast packets 0 broadcast packets
0 input packets 0 bytes
0 input packet drops
Tx
0 unicast packets 0 multicast packets 0 broadcast packets
0 output packets 0 bytes
0 flood packets
0 output packet drops
FABRIC-001-A(nxos)# show interface vethernet 931
Vethernet931 is down (nonParticipating)
Bound Interface is --
Port description is server 1/5, VNIC vNIC2
Hardware is Virtual, address is 002a.6a81.77a0
Port mode is trunk
Speed is auto-speed
Duplex mode is auto
300 seconds input rate 0 bits/sec, 0 packets/sec
300 seconds output rate 0 bits/sec, 0 packets/sec
Rx
0 unicast packets 0 multicast packets 0 broadcast packets
0 input packets 0 bytes
0 input packet drops
Tx
0 unicast packets 0 multicast packets 0 broadcast packets
0 output packets 0 bytes
0 flood packets
0 output packet drops
FABRIC-001-A(nxos)#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 10:45 AM
FABRIC-001-B# show service-profile circuit server 1/5
Service Profile: newDC1
Server: 1/5
Fabric ID: A
Path ID: 1
VIF vNIC Link State Oper State Prot State Prot Role Admin Pin Oper Pin Transport
---------- --------------- ----------- ---------- ------------- ----------- ---------- ---------- ---------
930 vNIC0 Error Error No Protection Unprotected 0/0 0/0 Ether
931 vNIC2 Error Error No Protection Unprotected 0/0 0/0 Ether
933 vNIC4 Up Active No Protection Unprotected 0/0 0/10 Ether
Fabric ID: B
Path ID: 1
VIF vNIC Link State Oper State Prot State Prot Role Admin Pin Oper Pin Transport
---------- --------------- ----------- ---------- ------------- ----------- ---------- ---------- ---------
929 vNIC1 Error Error No Protection Unprotected 0/0 0/0 Ether
932 vNIC3 Error Error No Protection Unprotected 0/0 0/0 Ether
934 vNIC5 Up Active No Protection Unprotected 0/0 0/11 Ether
FABRIC-001-B#

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 01:35 PM
Questions:
- do you run Ethernet End host mode
- do you have running uplinks to a Northbound switch
- is this the only SP having problem, other SP running ok ?
- do you have a static pin group ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-03-2014 11:39 PM
Make sure the blade is up and you have a OS installed. If you don't an OS installed or the blade is powered off you might see these errors.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2014 12:41 AM
Hello
Thats correct. I logged via KVM to the vaulty blade. OS was in BIOS mode.
Rebooted OS, and everything back to normal.
Thank you for your assist.
