Hi I would like to know if the UCS B200 M5 blade server is UL 60950-1 compliant
Forum Posts
Hello I am looking for the MTBF for the UCS B200 M5 blade server.
Hello All,I have a C220 M6N that will not power on. It appears the Intel ME Node Manager is "unhealthy or unresponsive" per the log and it's causing the server to not power on. I also have a corrupted BIOS, see logs below.Critical F1707 sys/rack-unit...
Hoping someone here has walked this exact path. I have a **UCS-E140DP-M1/K9** blade that I bought second-hand — no service contract, and the module is**past its Last Day of Support (2021-05-31)**. The x86 host side is completely fine; Windowsboots an...
I'm in the middle of upgrading a pair of FIs and after the first one rebooted, it came back up with an uplink port down. I'm curious if it's safe to reset the uplink port before proceeding to the second FI or should I proceed with the second FI's up...
We need to integrate our Cisco UCS/CIMC with HPE Aruba ClearPass TACACS+ for centralized authentication.UCS Model: BE7H-M5-K9CIMC Version: C240M5.4.3.2bCould someone please share the required CIMC configuration, TACAS parameters/attributes, and ...
We have the following connectedFabric Interconnect 6536 (UCS-FI-6536), 5108 Chassis with 2x IOM 2408 (UCS-IOM-2408 V03).We've cabled them with 100G QSFP28 to 4x25G SFP28 AOC 5M (NWP-QF-100G-S4-AOC-05-C)We've configured port as server port on initial ...
Need to replace a CPU on a UCS C240 M4 server as per https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C240M4/install/C240M4/replace.html#45480. However, the CPU that was delivered doesn't have the CPU plastic frame. So I'm not able to...
Could anyone validate this approach for updating our ESXI from v8.0 u3g -> ESXi 8.0 u3k please?Downloaded the vanilla image from VMWare for 8u3k from Broadcom site: VMware-ESXi-8.0U3k-25595708-depot.zipDownload Cisco_UCS_Addon_ESXi_80U3i_25205845_8.0...
I am installing cisco virtual connected appliance using vcenter client hosted on esxi host. I followed the installation steps from cisco (https://www.cisco.com/c/en/us/td/docs/unified_computing/Intersight/b_Cisco_Intersight_Appliance_Getting_Started_...
Was encouraged to cross post over here...Hoping that someone can assist me in figuring out an mystery... I have proxmox 9.2.4 installed on an HX240c-M5 server and am trying to bring up the interfaces on the VIC1457.My initial install did not utilize ...
We have a minor warning on a Fabric Interconnect relate to disk space."Disk usage for partition bootflash on fabric interconnect A exceeded 70%"Fabric Interconnect APartition Size (MB) Usedbootflash 16329 82opt 3877 4spare 5744 6var_sysmgr 2000 16var...
Hello,We are a VMware shop but we are looking to dip our toes into XenServer since it is included in our licensing. I've been searching around for a "best practices" guide for installing XenServer on UCS-X but not finding much. Hoping someone can p...
We recently acquired 5x Cisco C220 M5's off eBay and connected them to our existing UCS cluster. They have identical hardware layouts and pretty similiar firmware levels, and are all connected to our FI's through identical Cisco cables. But, only one...
Hi All, I've a Cisco UCS200M8 Server with firmware: 6.0 (2.260044)Server was previously connected to a FI 6454, During that time the server failed discovery due to firmware incompatibilty.After disconnecting the server from the FI, i'm now trying to ...
