Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Pravin Phadte
Stats
Member since
12-06-2006
516
Posts
271
Helpful
26
Solutions
Created by
Pravin Phadte
in Switching
in Switching
02-15-2013
02:33 AM
02-15-2013
02:33 AM
I would suggest to upgrade the ios this might be related to a bug
... View more
Created by
Pravin Phadte
in Network Management
in Network Management
07-26-2012
08:31 AM
07-26-2012
08:31 AM
i also tried cant find anything that can monitor this right now
... View more
Created by
Pravin Phadte
in Other Data Center Subjects
in Other Data Center Subjects
06-18-2012
05:26 AM
06-18-2012
05:26 AM
you will have to retrive the password. check the link http://www.cisco.com/en/US/products/hw/ps4159/ps4358/products_password_recovery09186a00801258c3.shtml
... View more
05-05-2010
08:07 AM
may be somthing to do with authorization. Check the settings in asdm again.
... View more
05-05-2010
08:03 AM
Hi, 1. When u say no traffic is flowing .. what do u mean you are unable to ping ? 2. How many tunnels are configued on ASA and on RVS4000? I see the the traffic on the tunnel on ASA end. - Check the access-list again.(subnet mask) - Clear the tunnel on ASA end. (clear crypto isakmp sa) or (clear crypto isakmp sa perr x.x.x.x) Regards, Pravin
... View more
12-16-2009
11:48 PM
First check the flash if you have image of asdm: show flash: asdm-615.bin would be the image name may be 611 also depends. as per the image in flash config boot (its not in your configs) asdm image disk0:/asdm-XXX.bin Update you java on machine which you would be accessing the ASDM just in case. Neuromancer....
... View more
12-16-2009
11:43 PM
For RA no dint see this issuie but yes for Site-to-Site there were problem with this Image on ASA. Seems like you have hit a bug. Neuromancer..
... View more
12-16-2009
11:41 PM
Did you try to ping from you machine to the printer ? If the ping did work. You can try to http or https to that ip and see if you are able to reach the printer ? neuromancer
... View more
12-16-2009
11:39 PM
No issuies till now wil ssl vpn and anyconnect. It seems to be good. neuromancer...
... View more
12-16-2009
11:36 PM
You need to check the remote firewall configs do. 1. crypto map VPN 10 set transform-set VPN What have you set. Is it sameon both ends ? 2. isakmp key ******** address 11.11.11.11 netmask 255.255.255.255 Are us sure about the key which u have added in this. HTH
... View more
12-16-2009
11:33 PM
Check the link below it will help in auto singon configs http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008067e9ff.shtml HTH
... View more
11-20-2009
06:31 AM
below is one more link if you need to compare the 5500 models http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80402e39.html#wp9000076
... View more
11-20-2009
06:24 AM
fine by default the pfs is in group 2. can you check with adding the below command crypto map OUTSIDE_map 57 set pfs group2 do clear crypto ipsec sa peer
... View more
11-20-2009
06:10 AM
I would suggest to remove this staements. crypto isakmp policy 50 authentication pre-share encryption 3des hash sha group 1 lifetime 86400 Since you are using group 2 only. Could you also reload the ISP device and the firewall if possible. HTH pravin
... View more
Created by
Pravin Phadte
in Network Security
in Network Security
11-19-2009
09:42 PM
11-19-2009
09:42 PM
Both show connection and show local host would povide you with output for tcp. But this would be a huge output and diffucult to find a single ip in production network. A good tool we use is fireplotter which poovides the output for about. Its good one. Regards Pravin
... View more
Created by
Pravin Phadte
in Network Management
07-26-2012
07-26-2012
i also tried cant find anything that can monitor this right now
Created by
Pravin Phadte
in Other Data Center Subjects
06-18-2012
06-18-2012
you will have to retrive the password.check the
linkhttp://www.cisco.com/en/US/products/hw/ps4159/ps...
05-05-2010
Hi,1. When u say no traffic is flowing .. what do u mean you are unable
to ping ?2. How many tunnels...
12-16-2009
First check the flash if you have image of asdm:show flash:asdm-615.bin
would be the image name may ...
12-16-2009
For RA no dint see this issuie but yes for Site-to-Site there were
problem with this Image on ASA.Se...
Created by
Pravin Phadte
in VPN
12-16-2009
12-16-2009
Did you try to ping from you machine to the printer ?If the ping did
work. You can try to http or ht...
12-16-2009
You need to check the remote firewall configs do.1. crypto map VPN 10
set transform-set VPNWhat have...
Created by
Pravin Phadte
in VPN
12-16-2009
12-16-2009
Check the link below it will help in auto singon
configshttp://www.cisco.com/en/US/products/ps6120/p...
11-20-2009
below is one more link if you need to compare the 5500
modelshttp://www.cisco.com/en/US/prod/collate...
11-20-2009
fine by default the pfs is in group 2.can you check with adding the
below commandcrypto map OUTSIDE_...
11-20-2009
I would suggest to remove this staements.crypto isakmp policy
50authentication pre-shareencryption 3...
Created by
Pravin Phadte
in Network Security
11-19-2009
11-19-2009
Both show connection and show local host would povide you with output
for tcp.But this would be a hu...
Public Statistics
| Date Registered | 12-06-2006 08:55 AM |
| Date Last Visited | 08-18-2017 03:53 AM |
| Total Messages Posted | 516 |
| Total Helpful Votes Received | 271 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 4 | |
| 4 | |
| 4 | |
| 4 |
.jpg "Hall of Fame Master"){kind=icon}
