About giuseppe.tetti1

giuseppe.tetti1 · 03-02-2023

Dear all, we have following NEXUS: NEXUS# sh verCisco Nexus Operating System (NX-OS) SoftwareSoftware BIOS: version 2.12.0 kickstart: version 8.2(1) system: version 8.2(1) Hardware cisco Nexus7000 C7009 (9 Slot) Chassis ("Supervisor Modul...

giuseppe.tetti1 · 02-20-2023

Dear all, we have bought FLEX licences for CUCM 14.0. We need to download CUCM locales from Software Central. We suppose, we can do it, becouse FLEX licenses include support. Unfortunatly, once logged in with our smart account, we can't download loca...

giuseppe.tetti1 · 07-19-2022

We need to hear outside dial tone when pressing the line botton on CUCM phone without pressing 0. Is there any way to do it ? Thank you for your kind help. Giuseppe

giuseppe.tetti1 · 03-03-2020

Dear all,we have configured, on a ISR4331/K9, Cisco IOS XE Software, Version 16.07.0 Cisco IOS Software [Fuji], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Versi on 16.7.1, RELEASE SOFTWARE (fc6), the following set of commands: controller E1 0/1/...

giuseppe.tetti1 · 12-17-2019

Dear all,we have to upgrade CUCM based on BE6K from 10.5 to 12.5. Can you suggest me how to upgrade VMware installed on BE6K in order to upgrade the CUCM as well.Thank you for your kind help.RegardsGiuseppe

giuseppe.tetti1 · 06-06-2023

I have the same need to understand SFP right model for C9300X-12Y-E, on-board optics, Cisco branded. We have to implement fiber optics OM4 link 1/10 Gbps. I have found "SFP-10/25G-CSR-S", that works at 10/25 Gbps, could it be the right one ? What if ...

giuseppe.tetti1 · 03-15-2023

Tried, unfortunatly it doesn't work.

giuseppe.tetti1 · 03-14-2023

Here, from vlan5: Castel_Fusano#traceroute 10.50.100.1 source vlan 5 (10.50.160.5)Type escape sequence to abort.Tracing the route to 10.50.100.1VRF info: (vrf in name/id, vrf out name/id) 1 10.50.160.1 2 msec 3 msec 3 msec 2 * * * 3 * * * 4...

giuseppe.tetti1 · 03-09-2023

Here what you are requested: Castel_Fusano#traceroute 10.50.100.1 source vlan 6 (10.50.190.5)Type escape sequence to abort.Tracing the route to 10.50.100.1VRF info: (vrf in name/id, vrf out name/id) 1 10.50.190.1 3 msec 3 msec 3 msec 2 * * * ...

giuseppe.tetti1 · 03-08-2023

Here is config of the other site, just see tunnel 55: interface Tunnel4 description tunnel per LDP in conformita' alla VLAN ERG ip address 10.250.250.1 255.255.255.252 ip pim sparse-dense-mode tunnel source 172.18.8.250 tunnel destination 10.110.255....

Member Since	‎10-28-2016 03:37 AM
Date Last Visited	‎06-14-2023 12:03 AM
Posts	35

User Statistics

User Activity

NEXUS 7k doesn't encapsulate on Tunnel GRE

Access to CUCM locale on Software Central

Change line tone on CUCM phone

"clock source line primary" disappear after a lack of power

VMWare Upgrade on BE6k

Re: Transceiver modules for C9300X-12Y-E

Re: NEXUS 7k doesn't encapsulate on Tunnel GRE

Re: NEXUS 7k doesn't encapsulate on Tunnel GRE

Re: NEXUS 7k doesn't encapsulate on Tunnel GRE

Re: NEXUS 7k doesn't encapsulate on Tunnel GRE