Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Mohamed Haneefa
Stats
Member since
09-05-2010
22
Posts
2
Helpful
0
Solutions
03-28-2017
06:31 AM
Hello Jaime
what is the reason for 9971 phones getting delay to turn on display,when phone was in idle stage.sometime it took 6 seconds to turn on.
... View more
01-28-2017
10:47 PM
Hi Baqari
Thanks for the response.i didn't try to downgrade it,as i always updated it from apple store.let me know the downgrade process for iPhone jabber.
... View more
Created by
Mohamed Haneefa
in IP Telephony and Phones
in IP Telephony and Phones
01-09-2017
02:43 AM
01-09-2017
02:43 AM
Hello Am using Cisco jabber 11.8.0.24 - 64 bit version on my IPhone IOS (10.2) and it is running on CUCM 11.x as well.
I have facing a problem that when a call is connected in jabber, the keypad is getting disabled. This is only in times when the call is received in lock-mode or when its running in the background. But there is no issues when jabber is in foreground, it could receive audio and video call with keypads active.At the same time ,I have tested in an android jabber phone, the keypad is working fine with both lock & unlock mode.
Jabber registered with CUCM as Phone service only. does anyone has facing this issue !!!!!
... View more
Labels:
06-29-2016
04:51 AM
Hi
Its me haneef here.am also facing with 9971 SIP Phones taking time to turn on. When phones are in idle state is getting delayed to turn ON (4 sec),Also if the phone is in off hook for dialing the PSTN is getting delayed to connect. At the same time we have some SCCP phones like 7975 are not showing this delay with the same network.
As I have changed the inter digit timeout (T302 = 3000) in CUCM and voice gateway parameter for quickly connect to PSTN. After that it get some improvement. But phones are still getting delayed to display.Now we want to reduce this overall processing time.
we are not using any overlap on any route pattern!!!!!!!!!!!
Network Layout
============
Cisco Unified Communication Manager (UCS -220-M3)
CUCM 11.0.1 == T302 timer is 3000
Voice Gateway-2811
VGW == Inter digit timeout 2 sec
Gateway Protocol == H323
Any suggestions
regards,
Haneef
... View more
06-29-2016
01:04 AM
Jaime Valencia
Thanks for the information .we are not using any overlap on any route pattern!!!!!!!!!!!
your prompt response in this regard will be highly appreciated
... View more
Created by
Mohamed Haneefa
in IP Telephony and Phones
in IP Telephony and Phones
06-28-2016
03:56 PM
06-28-2016
03:56 PM
Hi
Am facing with 9971 SIP phones taking time to connect call outside. When phones are in idle state is getting delayed to turn ON (4 sec),if the phone is in off hook state for dialing the PSTN is also taking time to connect. At the same time we have some SCCP phones like 7975 are not showing this delay with the same network.
As I have changed the inter digit timeout (T302 = 3000) in CUCM and voice gateway parameter for quickly connect to PSTN. After that it seems to be fast..But phones are still getting delayed to display.I want to reduce this overall processing time.
* we are not using any overlap on any route pattern!!!!
* There is no such difference ,even i tried to make a sip dial rule on the 9971 phone itself...
Network Layout
============
Cisco Unified Communication Manager (UCS -220-M3)
CUCM 11.0.1 == T302 timer is 3000
Voice Gateway-2811
VGW == Inter digit timeout 2 sec
Gateway Protocol == H323
Please let me know ,If any suggestions ,!!!!
regards,
Haneef
... View more
- Tags:
- !cucm ip-phone call flow
- #h323 #cucm #Gateway #PSTN
- #voice #sip #9971 #one way audio #MGCP #pri
- IP Telephony Dial Plan
Labels:
Created by
Mohamed Haneefa
in IP Telephony and Phones
in IP Telephony and Phones
09-09-2015
07:28 AM
09-09-2015
07:28 AM
Dear Laith Thank you for your information. please find my network as follows !!!! CME 10.11.7.2 Subnet 255.255.255.0 IP Phone 10.11.8.x Subnet 255.255.255.0 Default gateway 10.11.8.1 yes DGW is core switch... do you have any template to create a multicast for paging between CME and core switch? you can use my above network information to create a sample config. !!!!.
... View more
09-07-2015
08:43 AM
Dear laith let me tell you first of all,I did configured as multicast ( paging-dn 86 multicast ).it wont work.then i use to configure as uni-cast,it woks only up to 10 SCCP phone at a time.I have never been configure for multicast address in CME. could you show me how to configure it.below find the CME and IP phone informations as follows !!!! CME 10.11.7.2 Subnet 255.255.255.0 IP Phone 10.11.8.x Subnet 255.255.255.0
... View more
09-03-2015
01:04 AM
Dear Experts.... After long time ,I use to created a paging service on my client in CME as follows..... ephone-dn 86 name Paging number 1234 paging ip 239.1.1.10 port 2000 ephone 1 mac-address 8478.ACC6.958A button 1:1 paging-dn 86 unicast ephone 2 mac-address 5475.D02A.F36E button 1:2 paging-dn 86 unicast ephone 3 mac-address 8478.ACC6.997E button 1:3 paging-dn 86 unicast My problem is simple,when i use to dial on page number as 1234 ,its working with all connected page-dn's,After disconnect from page service some of telephones(6921) are not getting the dial tone ,even can't call internally or simply say phone get hang.does any one face this issue so far.please check my check above config & let me know your suggestion here!!!! !!!!!!!!!!& one more thing ,as my client using both sip & sccp types. is there any extra configuration needed for paging for communicating between SIP & SCCP?..
... View more
Labels:
06-26-2014
12:47 AM
Me too facing smiler issue @ Jaime Valencia @ Manish Gogna I have some 6921 ip phones are newly shipped , but not showing missed call info in Call records.below mention the detail as follows -> If CUCM version is 7.1.3 -> Successfully running 6921 IP Phones ( old firmware ver : 9.0.2.0 ) -> Missed call info in Call records not seen ( newly firmware ver : 9.3.1.3) From the Downloads i found that CUCM 7.1.3 Supports maximum up to 9.2(1) . How should i Proceed to get the new ip phones to show missed calls in call records ?
... View more
Created by
Mohamed Haneefa
in IP Telephony and Phones
in IP Telephony and Phones
08-13-2013
09:21 AM
08-13-2013
09:21 AM
does anyone knows above mention subject....
... View more
Labels:
01-05-2013
12:55 AM
Dear Chris As of now there is no WAN conectivity between these sites.The CUCM is located in the HQ.from here the many conectivity to diferent sites, also we have ASA MPLS technology etc.i dont have any option to upgrade from CUCM 7 to 8.i just want to know the existing network ,how it would be posible.could you clarify the following things as it is mentioned ur above replay. --why did you say QOS is not guarantee...(codec g729?) ----which type of IP phone model supported for this scenario.(feature,vpn....) -----what i have to confirmed in the remote site configuration..(in site, router -> 1941,switch-> 2960 and dynamic public IP) ------we have to configure in the site limited phones only...(just only 5 phones conected to HQ) -------could you share your any costomer topology or share your experience. regards Mohd Haneef
... View more
Created by
Mohamed Haneefa
in IP Telephony and Phones
in IP Telephony and Phones
12-30-2012
10:43 PM
12-30-2012
10:43 PM
Dear All I have a new task for configuring a remote site IP telephone register to my running CUCM 7.1.3, in remote site there is no any call processing system,only one 1941 router ,one 2960 switch with POE and one public IP. by default CUCM 7.1.3 does'nt have VPN facility.could u suggest a network setup such as from our side to remote site.i want to know each step by step from both side.i hope any one can give a solution !!!!!!!!!! regards Mohd Haneef
... View more
Labels:
12-30-2012
10:22 PM
Dear all I have a new task for configuring a remote site IP telephone register with my call manager 7.1.3,in remote site there is no call manager system,only one 1941 router ,one 2960 switch and one public IP. by default CUCM 7.1.3 does'nt have VPN facility.could u suggest a network toplogy such as from our side to remote site.i want to know each step by step from both side.i hope u can give a solution !!!!!!!!!! regards Mohd Haneef
... View more
12-18-2012
12:45 AM
Dear All Am going to buy new extra device licence unit (DLU) for compansating with this over subscribed DLU licenses as seen by the negative number.my current CUCM version is 7.1.3, is it support DLU pack still now? or i have to buy new user connect license(UCL) ? or have to upgrade my current CUCM ?.let me know a short note on this steps. regards Mohd Haneef
... View more
03-28-2017
Hello Jaime what is the reason for 9971 phones getting delay to turn on
display,when phone was in id...
Created by
Mohamed Haneefa
in Collaboration Applications
01-31-2017
01-31-2017
Hello kelliIts already in the cisco forum. Didn't get any specific
solution in this regards. Thank y...
01-28-2017
Hi Baqari Thanks for the response.i didn't try to downgrade it,as i
always updated it from apple sto...
Created by
Mohamed Haneefa
in Collaboration Applications
01-28-2017
01-28-2017
HelloAm facing a problem in IPhone jabber. when a call is connected in
jabber, the keypad is getting...
01-09-2017
HelloAm using Cisco jabber 11.8.0.24 - 64 bit version on my IPhone IOS
(10.2) and it is running on C...
06-29-2016
Hi Its me haneef here.am also facing with 9971 SIP Phones taking time to
turn on. When phones are in...
06-29-2016
Jaime Valencia Thanks for the information .we are not using any overlap
on any route pattern!!!!!!!!...
Created by
Mohamed Haneefa
in IP Telephony and Phones
06-28-2016
06-28-2016
Hi Am facing with 9971 SIP phones taking time to connect call outside.
When phones are in idle state...
09-09-2015
Dear Laith Thank you for your information. please find my network as
follows !!!!CME 10.11.7.2 Subne...
09-07-2015
Dear laith let me tell you first of all,I did configured as multicast
(paging-dn 86 multicast).it wo...
09-03-2015
Dear Experts.... After long time ,I use to created a paging service on
my client in CME as follows.....
06-26-2014
Me too facing smiler issue @Jaime Valencia @Manish Gogna I have some
6921 ip phones are newly shippe...
Created by
Mohamed Haneefa
in IP Telephony and Phones
08-13-2013
08-13-2013
does anyone knows above mention subject....
01-05-2013
Dear Chris As of now there is no WAN conectivity between these sites.The
CUCM is located in the HQ.f...
Created by
Mohamed Haneefa
in IP Telephony and Phones
12-30-2012
12-30-2012
Dear All I have a new task for configuring a remote site IP telephone
register to my running CUCM 7....
Public Statistics
| Date Registered | 09-05-2010 01:06 AM |
| Date Last Visited | 11-13-2019 12:39 AM |
| Total Messages Posted | 22 |
| Total Helpful Votes Received | 2 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 11 | |
| 6 | |
| 2 | |
| 3 | |
| 3 |
.jpg "Hall of Fame Cisco Employee"){kind=icon}
