Hello Dennis. In CUCM yes, it is the same Route Pattern, but even I tested with anothers Route Pattern. On the Voice Gateway no, there are two dialpeer one for Belgium and the other for Brasil, and I tryed with only one dialpeer too, but is the same result. I forgot to mention that I use and E1 R2 digital. These are the dialpeer for those numbers. This one is for Belgium. dial-peer voice 9001 pots trunkgroup PSTN-AXTEL description **llamadas Internacionales AXTEL** destination-pattern 900T prefix 00 And This other one is for Brasil. dial-peer voice 9005 pots trunkgroup PSTN-AXTEL description "Internacionales AXTEL" destination-pattern 9005T forward-digits 14 Config E1's. controller E1 0/0/0 framing NO-CRC4 line-termination 75-ohm ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani cas-custom 0 invert-abcd 0 0 1 1 country telmex reanswer-time 1000 category 2 answer-signal group-b 1 ani-digits min 0 max 10 groupa-callerid-end trunk-group PSTN-AXTEL description Llamadas Axtel 1493-3000 ! controller E1 0/1/0 framing NO-CRC4 line-termination 75-ohm ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani cas-custom 0 invert-abcd 0 0 1 1 country telmex reanswer-time 1000 category 2 answer-signal group-b 1 ani-digits min 0 max 10 groupa-callerid-end trunk-group PSTN-AXTEL description Llamadas Axtel 8135-8900 ! controller E1 0/1/1 framing NO-CRC4 line-termination 75-ohm ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani cas-custom 0 country telmex category 2 answer-signal group-b 1 caller-digits 4 groupa-callerid-end trunk-group PSTN-AXTEL description PSTN-AXTEL 14933000 ... View more

Thanks Jason. That is correct, i want to forward the calls comes inbound to a specific extension, I modify the voice translation rule, but no call comes, good, call come to the trunk, but don't know where to send it, I just know if my configuration is correct or i missing something. ... View more

Sorry. The above is in the UC540 equipment. ... View more

Hi help me please. i have a problem whit the FAC (Force Autoritation Code). I set the dial-peer.  However, when digit number, just take de Dial-Peer  101 Voip, asked the ID number and then the PIN number but, after dialing the key #, the call is cut. dial-peer voice 101 voip corlist outgoing call-CELULAR-LOCAL preference 1 service clid_authen_collect destination-pattern 9044.......... voice-class codec 1 session target ipv4:10.1.1.1 incoming called-number 9044.......... dtmf-relay h245-alphanumeric no vad ial-peer voice 51 pots corlist outgoing call-CELULAR-LOCAL preference 2 destination-pattern 9044.......... port 0/1/1 forward-digits 13 no sip-register I put a "Show voice call status" and showme this: UC520#sh voice call status CallID     CID  ccVdb      Port             DSP/Ch  Called #   Codec    MLPP Dial-peers 0x36A      1F0B 0x872DF234 50/0/11.0                5515125936 g711ulaw       20006/101 1 active call found Namely take the dial-peer 101  but not take the dial-peer 51, and this is the port where the call goes out. Thanks for help me. ... View more

Then do not recommend SA500 teams, because I have a client who asks me security on three levels, specifically Web access control, but also the VLAN's to segment broadcast domain, you know if you can create sub-SA540 interfaces communicate between VLANs? ... View more

Thanks Alexander. Do you mean the package to be installed at UC? I install the package UC540-8.2.0, is this is going to improve in May? ... View more

Ok thanks Cyndi verify that. ... View more