Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About jc.saavedra
10-09-2017
jc.saavedra
Member since
02-21-2011
Beginner
11-06-2014
07:39 AM
Thanks a lot Suresh!!! The issue was generated by codec mismatch ITSP g711a - CME g711u - CUCM g711u and I Don't have configured a destination-pattern to inbound. THANKS! The final config is: dial-peer voice 67 voip description ** SIP trunk ITSP** destination-pattern 591[67]....... no translation-profile incoming 1 session protocol sipv2 session target ipv4:172.17.0.# session transport udp voice-class sip early-offer forced dtmf-relay sip-notify no dtmf-interworking codec g711alaw ! dial-peer voice 68 voip description ** SIP trunk CUCM** answer-address .T destination-pattern 752##### session protocol sipv2 session target ipv4:172.16.6.# voice-class sip early-offer forced dtmf-relay sip-notify codec g711alaw !
... View more
Created by
jc.saavedra
in IP Telephony and Phones
in IP Telephony and Phones
11-06-2014
05:26 AM
11-06-2014
05:26 AM
Hi Everybody, I Have an issue with a ITSP SIP TRUNK, the issue apparently is "SIP/2.0 488 Not Acceptable Media". I Tried several things already, I Don´t know how to resolve this issue. The outbound calls is already OK, the problem is with the inbound calls: from the ITSP to the CUCM. I Have this topology to the ITSP SIP TRUNK: ITSP --- sip --- CME --- sip --- CUCM The configuration of CME is: dial-peer voice 67 voip description ** SIP trunk ITSP** destination-pattern 591[67]....... session protocol sipv2 session target ipv4:172.17.0.13 session transport udp voice-class sip early-offer forced no dtmf-interworking codec g711ulaw ! dial-peer voice 68 voip description ** SIP trunk CUCM** answer-address .T session protocol sipv2 session target ipv4:172.16.6.3 voice-class sip early-offer forced codec g711ulaw ! sip-ua disable-early-media 180 connection-reuse ! voice service voip ip address trusted list ipv4 0.0.0.0 ipv4 0.0.0.0 0.0.0.0 allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h450.7 no supplementary-service sip moved-temporarily no supplementary-service sip refer fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none sip bind control source-interface GigabitEthernet0/1.5 bind media source-interface GigabitEthernet0/1.5 registrar server early-offer forced ! On the CUCM Side: Media Termination Point (checked) Disable Early Media on 180 (unchecked) Require SDP Inactive Exchange for Mid-Call Media Change(checked) Early Offer support for voice and video calls (checked) Send send-receive SDP in mid-call INVITE(checked) The result of "debug ccsip messages" and "debug dialpeer voice inout" is: 001062: 03:31:03: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: INVITE sip:69200020@172.16.10.2:5060;user=phone SIP/2.0 Via: SIP/2.0/UDP 172.17.0.11:5060;branch=z9hG4bKi2mhl410do70mrc4s141.1 Call-ID: bb1rkaxkjaxx4vkv3y1u1y3xxqa2k12b@10.18.5.64 From: "70965999"<sip:70965999@172.17.0.11;transport=udp;user=phone>;tag=2u2uavrx-CC-1013 To: "69200020"<sip:69200020@172.16.10.2;transport=udp;user=phone> CSeq: 1 INVITE Max-Forwards: 69 Contact: <sip:172.17.0.11:5060;transport=udp> Allow: INVITE,ACK,OPTIONS,BYE,CANCEL,INFO,PRACK,NOTIFY,MESSAGE,UPDATE P-Asserted-Identity: <tel:70965999> Supported: 100rel,histinfo,precondition P-Early-Media: supported Content-Length: 362 Content-Type: application/sdp v=0 o=HuaweiSoftx3000 1102026905 1102026906 IN IP4 172.17.0.11 s=SipCall c=IN IP4 172.17.0.11 t=0 0 m=audio 10386 RTP/AVP 8 18 116 a=rtpmap:8 PCMA/8000 a=rtpmap:18 G729/8000 a=rtpmap:116 telephone-event/8000 a=ptime:5 a=curr:qos local sendrecv a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos optional remote sendrecv a=3gOoBTC 001063: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore: Calling Number=69200020, Called Number=69200020, Peer Info Type=DIALPEER_INFO_SPEECH 001064: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore: Match Rule=DP_MATCH_DEST; Called Number=69200020 001065: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore: No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1) 001066: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin: dialstring=69200020, saf_enabled=1, saf_dndb_lookup=1, dp_result=-1 001067: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg: Result=NO_MATCH(-1) 001068: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore: Calling Number=70965999, Called Number=, Voice-Interface=0x0, Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE, Peer Info Type=DIALPEER_INFO_SPEECH 001069: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore: Result=Success(0) after DP_MATCH_ANSWER; Incoming Dial-peer=68 001070: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin: dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0 001071: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore: Calling Number=70965999, Called Number=, Voice-Interface=0x0, Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE, Peer Info Type=DIALPEER_INFO_SPEECH 001072: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore: Result=Success(0) after DP_MATCH_ANSWER; Incoming Dial-peer=68 001073: 03:31:03: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin: dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0 001074: 03:31:03: //-1/CD12136099D5/DPM/dpAssociateIncomingPeerCore: Calling Number=70965999, Called Number=69200020, Voice-Interface=0x0, Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE, Peer Info Type=DIALPEER_INFO_SPEECH 001075: 03:31:03: //-1/CD12136099D5/DPM/dpAssociateIncomingPeerCore: Result=Success(0) after DP_MATCH_ANSWER; Incoming Dial-peer=68 001076: 03:31:03: //-1/CD12136099D5/DPM/dpMatchSafModulePlugin: dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0 SIP: Trying to parse unsupported attribute at media level 001077: 03:31:03: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 488 Not Acceptable Media Via: SIP/2.0/UDP 172.17.0.11:5060;branch=z9hG4bKi2mhl410do70mrc4s141.1 From: "70965999"<sip:70965999@172.17.0.11;transport=udp;user=phone>;tag=2u2uavrx-CC-1013 To: "69200020"<sip:69200020@172.16.10.2;transport=udp;user=phone>;tag=C139A0-1755 Date: Thu, 06 Nov 2014 13:01:04 GMT Call-ID: bb1rkaxkjaxx4vkv3y1u1y3xxqa2k12b@10.18.5.64 CSeq: 1 INVITE Allow-Events: telephone-event Reason: Q.850;cause=65 Server: Cisco-SIPGateway/IOS-15.3.3.M2 Content-Length: 0 001078: 03:31:03: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: GatewayTelf_JD#ACK sip:69200020@172.16.10.2:5060;user=phone SIP/2.0 Via: SIP/2.0/UDP 172.17.0.11:5060;branch=z9hG4bKi2mhl410do70mrc4s141.1 CSeq: 1 ACK Call-ID: bb1rkaxkjaxx4vkv3y1u1y3xxqa2k12b@10.18.5.64 From: "70965999"<sip:70965999@172.17.0.11;transport=udp;user=phone>;tag=2u2uavrx-CC-1013 To: "69200020"<sip:69200020@172.16.10.2;transport=udp;user=phone>;tag=C139A0-1755 Max-Forwards: 69 Content-Length: 0 Some light at the end of of the tunnel? Thanks in advance!!
... View more
Labels:
10-23-2014
03:13 PM
Hi clougher01 I'm in the same problem, my topology: CUCM -> sip trunk -> CME -> sip trunk -> ITSP When I Answer the call is hang up. My config is dial-peer voice 67 voip description ** SIP trunk ITSP** destination-pattern 591[67]....... session protocol sipv2 session target ipv4:172.17.0.9 session transport udp voice-class sip early-offer forced codec g711ulaw ! dial-peer voice 68 voip description ** SIP trunk CUCM** session protocol sipv2 answer-address .T session target ipv4:172.16.6.3 voice-class sip early-offer forced codec g711ulaw I Have SIP to SIP and the CUCM configured. bind media source-interface GigabitEthernet0/0 (CME to CUCM Iface) Do you guide me? Thanks.
... View more
10-16-2014
12:45 PM
Hi Vattullu, this option is editable? For example 2 devices maximun. If yes, where? Thanks!
... View more
09-04-2014
05:56 AM
Thanks Moin, We have to configure the port with authentication host-mode multi-domain and remove the por-security. Thank you.
... View more
Created by
jc.saavedra
in Network Management
in Network Management
09-03-2014
01:10 PM
09-03-2014
01:10 PM
Hello Supporters, We have some problems with Prime Infrastructure, the problems are deploy config related. Currently We have this log in System Events: Severity: Critical Messages: NCS disk volume 'optvol' is above the recommend disk usage, '88'% used. The disk space is: Disk Source Available Space(KB) Used Space(KB) % Used /dev/mapper/smosvg-rootvol 3415992 346888 9 /dev/mapper/smosvg-storeddatavol 7344280 2047972 22 /dev/mapper/smosvg-localdiskvol 25195836 3010848 11 /dev/sda2 88342 5688 6 /dev/mapper/smosvg-home 84621 5659 6 /dev/mapper/smosvg-optvol 14574888 104122044 88 Cisco Prime Infrastructure Version: 1.3 (1.3.0.20) Could someone help us? Thanks.
... View more
Labels:
Created by
jc.saavedra
in Network Management
in Network Management
09-03-2014
07:45 AM
09-03-2014
07:45 AM
Hello, I'm trying to deploy a configuration by Cisco Prime Infrastructure v1.2: The config that I want to deploy (is a test) is the following: conf t ! interface GigabitEthernet1/0/37 no switchport port-security no switchport port-security aging time 5 no switchport port-security violation restrict no switchport port-security aging type inactivity no switchport port-security maximum 3 shutdown no shutdown The result of failed operation is: IFM Config | CA Backup failed before deploy template test_portsecurity to 172.18.8.26 Someone has resolve this problem?
... View more
Labels:
09-01-2014
07:51 AM
Hi Neno, The scenario is: on the same SW port I have configured: interface GigabitEthernet1/0/25 description PC Jeremias Castro switchport access vlan 2008 switchport mode access switchport voice vlan 2108 switchport port-security maximum 3 switchport port-security switchport port-security aging time 5 switchport port-security violation restrict switchport port-security aging type inactivity ip arp inspection limit rate 30 authentication event fail action next-method authentication event server dead action authorize vlan 2008 authentication event server dead action authorize voice authentication event server alive action reinitialize authentication host-mode multi-auth authentication open authentication order dot1x mab authentication priority dot1x mab authentication port-control auto authentication violation restrict mab macro description Phone-Host dot1x pae authenticator dot1x timeout tx-period 3 spanning-tree portfast The port is configured to work with 802.1x and Port-security. The question is, what is the problem if I have this config. Thank you.
... View more
08-29-2014
02:00 PM
Hi everyone, I'm implemmenting ISE in a network with Port Security enabled. According the book Cisco ISE for BYOD and Secure Unified Access Port-security is not compatible with 802.1x. I want to know what is the affectation of to have Port-security and 802.1x enabled on the same SW Port. Someone? Thanks!
... View more
Labels:
Created by
jc.saavedra
in IP Telephony and Phones
in IP Telephony and Phones
04-01-2014
08:07 AM
04-01-2014
08:07 AM
To resolve the DTMF issue I´m using "dtmf-relay rtp-nte" under pool and dial-peer. But my problem is more complicated, when add Sip-notify or something all the Phones that re-register get busy tone at first digit dialed. This look like a bug on the IOS.
... View more
Created by
jc.saavedra
in IP Telephony and Phones
in IP Telephony and Phones
03-31-2014
07:50 AM
03-31-2014
07:50 AM
Hi everyone. I have a issue that is killing me... We have a CME on Router 2951, all is run fine until we start to configure the CUE for an autoattendant. The problem was with DTMF don´t recognize. Then I configure dtmf-relay sip-notify in both sides Voice register pool and Dial-peer voice to CUE. When I add the command DTMF-RELAY Sip-notify and create-profile all the phones fail in the call, get busy tone or reorder tone at first digit. The only way of ressolve this is restarting the router. Someone have this problem o similar? Help me please!!
... View more
Labels:
Created by
jc.saavedra
in IP Telephony and Phones
in IP Telephony and Phones
03-17-2014
09:37 AM
03-17-2014
09:37 AM
I complete the restore. I was trying to restore the Database from a subscriber (I think this is a better procedure) but this restore failed. When I select the option restore from backup instead of subscriber the restore success: restore completed. Select the server from which database data need to be restored: keep on --Not Selected-- and clic on restore button. Thank you so much.
... View more
Created by
jc.saavedra
in IP Telephony and Phones
in IP Telephony and Phones
03-17-2014
08:39 AM
03-17-2014
08:39 AM
Hi Aman, After upgrade from 7.1 to 9.1 we got some error on the Publisher server, resolved by the TAC, who suggested to perform a Rebuild of the Pubisher. I was take a complete backup, then a refresh install of the 9.1 version. I try to perform the restore fomr the backup and the result is this error on CCMDB.
... View more
03-17-2014
08:12 AM
Thank you for response Sree I´m sure the configuration data, the security password could to be different, at the beggining of restore ask me the security password. There is a way to perform restore from Backup and not from subscriber?
... View more
03-17-2014
06:15 AM
Yes, the credentials, security password and applications username are the same at the moment of backup. Only CCMDB get Fail state the others process are 100% completed.
... View more
11-06-2014 07:39 AM
Thanks a lot Suresh!!! The issue was generated by codec mismatch ITSP
g711a - CME g711u - CUCM g711u...
Created by
jc.saavedra
in IP Telephony and Phones
11-06-2014 05:26 AM
11-06-2014 05:26 AM
Hi Everybody, I Have an issue with a ITSP SIP TRUNK, the issue
apparently is "SIP/2.0 488 Not Accept...
10-23-2014 03:13 PM
Hi clougher01 I'm in the same problem, my topology: CUCM -> sip trunk ->
CME -> sip trunk -> ITSP Wh...
10-16-2014 12:45 PM
Hi Vattullu, this option is editable? For example 2 devices maximun. If
yes, where? Thanks!
09-04-2014 05:56 AM
Thanks Moin, We have to configure the port with authentication host-mode
multi-domain and remove the...
Created by
jc.saavedra
in Network Management
09-03-2014 01:10 PM
09-03-2014 01:10 PM
Hello Supporters, We have some problems with Prime Infrastructure, the
problems are deploy config re...
Created by
jc.saavedra
in Network Management
09-03-2014 07:45 AM
09-03-2014 07:45 AM
Hello, I'm trying to deploy a configuration by Cisco Prime
Infrastructure v1.2:The config that I wan...
09-01-2014 07:51 AM
Hi Neno, The scenario is: on the same SW port I have
configured:interface GigabitEthernet1/0/25 desc...
08-29-2014 02:00 PM
Hi everyone, I'm implemmenting ISE in a network with Port Security
enabled. According the book Cisco...
04-01-2014 08:07 AM
To resolve the DTMF issue I´m using "dtmf-relay rtp-nte" under pool and
dial-peer. But my problem is...
Created by
jc.saavedra
in IP Telephony and Phones
03-31-2014 07:50 AM
03-31-2014 07:50 AM
Hi everyone. I have a issue that is killing me... We have a CME on
Router 2951, all is run fine unti...
03-17-2014 09:37 AM
I complete the restore. I was trying to restore the Database from a
subscriber (I think this is a be...
03-17-2014 08:39 AM
Hi Aman, After upgrade from 7.1 to 9.1 we got some error on the
Publisher server, resolved by the TA...
03-17-2014 08:12 AM
Thank you for response SreeI´m sure the configuration data, the security
password could to be differ...
Public Statistics
| Date Registered | 02-21-2011 10:33 AM |
| Date Last Visited | 10-09-2017 02:06 PM |
| Total Messages Posted | 27 |
| Total Helpful Votes Received | 10 |
