Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Richard Simmons
Stats
Member since
12-18-2008
253
Posts
132
Helpful
23
Solutions
Certifications
01-27-2020
03:53 AM
missed your comment on setting the translation-profile outgoing - once i'd done that it works fine - thanks!
... View more
01-27-2020
03:42 AM
I tried adding a dial-peer with the loopback address and get the following error; %CALL_CONTROL-6-CALL_LOOP: The incoming call has a global identifier already present in the list of currently handled calls. It is being refused. Translation Pattern tests and Dial-peers below; SGW02#test voice translation-rule 4 461410 Matched with rule 2 Original number: 461410 Translated number: 6000 Original number type: none Translated number type: none Original number plan: none Translated number plan: none SGW02#test voice translation-rule 4 5000 Matched with rule 1 Original number: 5000 Translated number: 6000 Original number type: none Translated number type: none Original number plan: none Translated number plan: none dial-peer voice 1 pots translation-profile incoming ISDNIN incoming called-number . direct-inward-dial ! dial-peer voice 10 pots description *** Outbound Calls via ISDN *** destination-pattern 0T port 0/1/0:15 forward-digits all ! dial-peer voice 100 voip preference 2 destination-pattern 5... session protocol sipv2 session target ipv4:10.105.44.197 voice-class codec 1 voice-class sip options-keepalive voice-class sip bind control source-interface Loopback0 voice-class sip bind media source-interface Loopback0 dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad ! dial-peer voice 101 voip preference 3 destination-pattern 5... session protocol sipv2 session target ipv4:10.105.44.133 voice-class codec 1 voice-class sip options-keepalive voice-class sip bind control source-interface Loopback0 voice-class sip bind media source-interface Loopback0 dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad
... View more
01-24-2020
02:29 AM
Hi, I have a group of phones that register in SRST, the phones DN's do not match the DDI's, as such i want all the external inbound calls to route to all of the phones in a hunt group. I have created the hunt group and that can be dialed internally however external calls do not connect, snipped of config below; voice register global default mode no allow-hash-in-dn timeouts interdigit 5 system message Phone is in emergency mode max-dn 20 max-pool 40 timezone 21 ! voice register pool 1 translation-profile incoming SRST-IN id network 10.127.174.0 mask 255.255.255.0 dtmf-relay rtp-nte voice-class codec 1 ! voice hunt-group 20 parallel list 2001,2002,2003,2004,2005,2006,2007,2008,2009 pilot 6000 voice translation-rule 4 rule 1 /500./ /6000/ rule 2 /^46141./ /6000/ voice translation-profile SRST-IN translate called 4
... View more
Labels:
Created by
Richard Simmons
in IP Telephony and Phones
in IP Telephony and Phones
01-23-2020
02:16 AM
01-23-2020
02:16 AM
I found the fix for this, i hadn't populated the SIP address within the SRST reference on CUCM, once that was completed my original configuration started working.
... View more
Created by
Richard Simmons
in IP Telephony and Phones
in IP Telephony and Phones
01-22-2020
06:29 AM
01-22-2020
06:29 AM
when you say chose mode east - is that auto correct from mode esrst ? is it not possible just to use standard srst ?
... View more
Created by
Richard Simmons
in IP Telephony and Phones
in IP Telephony and Phones
01-22-2020
04:34 AM
01-22-2020
04:34 AM
Hi All, Having an issue getting 7841 phones to register to a 4431 router in SRST, none of my phones register to the router when CUCM's are shutdown. I have the following configuration; voice service voip ip address trusted list ipv4 10.105.44.xxx ipv4 10.105.44.xxx rtp-port range 16384 32768 allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw modem passthrough nse codec g711ulaw sip registrar server expires max 600 min 60 ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw ! voice class h323 1 h225 timeout tcp establish 5 ! voice register global default mode <-- mode srst not available, only mode esrst or mode cme no allow-hash-in-dn timeouts interdigit 5 system message Phone is in emergency mode max-dn 20 max-pool 40 ! voice register pool 1 translation-profile incoming SRST-IN id network 10.0.0.0 mask 255.0.0.0 dtmf-relay rtp-nte voice-class codec 1 any help would be greatly appreciated!
... View more
05-16-2017
04:03 AM
Hi,
bit late to the party on this one but i've just run into this issue. I have associated all of the vnics with vcon1, restarted the server but still running into this issue.
Any other steps i can take for this?
Thanks,
Richard
... View more
05-04-2017
12:14 PM
From FI-A
fex-1# show platform software cmcctrl fancontrol all fex-1# fex-1# fex-1# show platform software cmcctrl showi2c # I2C Bus Statistics Thu May 4 15:08:17 EDT 2017 # I2C Bus 1 busn=0 nseg=2 segment 0 local segment 1 extended wait_gt_deadline 27 error_pca9541_per_device: # I2C Bus 2 busn=1 nseg=5 segment 0 local segment 1 chassis norxack 192 wait_gt_deadline 2 segment 2 blade segment 3 fan segment 4 psu gilroy.counter.reserved 4366 gilroy.counter.released 4366 gilroy.counter.status_chassis_off 4518 error_pca9541_per_device:
# I2C Device Statistics iom.fru={SUCCESS=12} iom.rtc={SUCCESS=12} NAME=iom.woodside No such path /sys/devices/platform/fsl-i2c.1/i2c-0/0-0048 NAME=iom.dcdc0 detach_state driver iout iout_cal_offset iout_oc_fault_limit mfr_date mfr_id mfr_location mfr_model mfr_revision mfr_serial name ot_fault_limit ot_warn_limit temperature1 temperature2 vin vin_ov_fault_limit vin_uv_fault_limit vout vout_mode vout_n vout_ov_fault_limit vout_uv_fault_limit NAME=iom.dcdc1 detach_state driver iout iout_cal_offset iout_oc_fault_limit mfr_date mfr_id mfr_location mfr_model mfr_revision mfr_serial name ot_fault_limit ot_warn_limit temperature1 temperature2 vin vin_ov_fault_limit vin_uv_fault_limit vout vout_mode vout_n vout_ov_fault_limit vout_uv_fault_limit iom.gpio0={SUCCESS=1374} iom.gpio1={SUCCESS=1374} iom.gpio2={SUCCESS=1374} iom.gpio3={SUCCESS=2814} iom.temp.inlet1={SUCCESS=5251} iom.temp.inlet2={SUCCESS=5251} iom.temp.woodside={SUCCESS=4595} c.fru={SUCCESS=1} c.seeprom={SUCCESS=42} f.fm0.fru={SUCCESS=1} f.fm1.fru={SUCCESS=1} f.fm2.fru={SUCCESS=1} f.fm3.fru={SUCCESS=1} f.fm4.fru={SUCCESS=1} f.fm5.fru={SUCCESS=1} f.fm6.fru={SUCCESS=1} f.fm7.fru={SUCCESS=1} p.psu3.psmi={SUCCESS=3} p.psu0.fru={SUCCESS=1} p.psu1.fru={SUCCESS=1} p.psu1.psmi={SUCCESS=3} p.psu2.fru={SUCCESS=1} p.psu3.fru={SUCCESS=1} c.gpio0={ENXIO=8} c.gpio1={ENXIO=8} c.gpio2={ENXIO=8} c.gpio3={ENXIO=8} # I2C Driver sysctl entries sysctl: error: permission denied on key 'net.ipv4.route.flush' sysctl: error: permission denied on key 'kernel.cad_pid' sysctl: error: permission denied on key 'kernel.cap-bound' dev.i2c.disconnect_retry = 3 dev.i2c.post_trigger = 64 dev.i2c.norxack_blink = 5 dev.i2c.norxack_blink = 5 dev.i2c.fixup_blink = 0 dev.i2c.pca9541-workaround = 16 dev.i2c.wait_deadline = 30 dev.i2c.chassis_reservation.demand = 0 dev.i2c.chassis_reservation.lock_state = 2 dev.i2c.chassis_reservation.auto_release = 1 dev.i2c.chassis_reservation.on_demand = 0 dev.i2c.chassis_reservation.pause_gilroy_thread = 0 dev.i2c.chassis_reservation.min_notheld_ms = 150 dev.i2c.chassis_reservation.wait_extra_ms = 3000 dev.i2c.chassis_reservation.grace_ms = 750 dev.i2c.chassis_reservation.hold_ms = 1500 dev.i2c.chassis_reservation.wait_ms = 4500 dev.i2c.gilroy-debug-level = 3 dev.i2c.debug-level = 1 dev.i2c.pca9541-businit = 1 dev.i2c.pca9541-delay = 250 dev.i2c.bus2.write-cdelay = 100 dev.i2c.bus2.write-delay = 100 dev.i2c.bus1.write-cdelay = 30 dev.i2c.bus1.write-delay = 30
From FI-B
fex-1# show platform software cmcctrl fancontrol all Fan 0 Speed (FRONT): 9358 Fan 0 Speed (REAR): 9473 Fan 0 dutycycle: 100 Fan 1 Speed (FRONT): 9137 Fan 1 Speed (REAR): 9457 Fan 1 dutycycle: 100 Fan 2 Speed (FRONT): 9075 Fan 2 Speed (REAR): 9294 Fan 2 dutycycle: 100 Fan 3 Speed (FRONT): 8985 Fan 3 Speed (REAR): 9608 Fan 3 dutycycle: 100 Fan 4 Speed (FRONT): 9262 Fan 4 Speed (REAR): 9818 Fan 4 dutycycle: 100 Fan 5 Speed (FRONT): 9030 Fan 5 Speed (REAR): 9473 Fan 5 dutycycle: 100 Fan 6 Speed (FRONT): 8985 Fan 6 Speed (REAR): 9391 Fan 6 dutycycle: 100 Fan 7 Speed (FRONT): 9262 Fan 7 Speed (REAR): 9660 Fan 7 dutycycle: 100 fex-1# fex-1# fex-1# show platform software cmcctrl showi2c # I2C Bus Statistics Thu May 4 15:13:37 EDT 2017 # I2C Bus 1 busn=0 nseg=2 segment 0 local segment 1 extended wait_gt_deadline 9 error_pca9541_per_device: # I2C Bus 2 busn=1 nseg=5 segment 0 local segment 1 chassis norxack 199 wait_gt_deadline 2 segment 2 blade segment 3 fan norxack 7 wait_gt_deadline 205 segment 4 psu wait_gt_deadline 114 gilroy.counter.reserved 4572 gilroy.counter.released 4572 gilroy.counter.status_chassis_off 4572 error_pca9541_per_device:
# I2C Device Statistics iom.fru={SUCCESS=12} iom.rtc={SUCCESS=12} NAME=iom.woodside No such path /sys/devices/platform/fsl-i2c.1/i2c-0/0-0048 NAME=iom.dcdc0 detach_state driver iout iout_cal_offset iout_oc_fault_limit mfr_date mfr_id mfr_location mfr_model mfr_revision mfr_serial name ot_fault_limit ot_warn_limit temperature1 temperature2 vin vin_ov_fault_limit vin_uv_fault_limit vout vout_mode vout_n vout_ov_fault_limit vout_uv_fault_limit NAME=iom.dcdc1 detach_state driver iout iout_cal_offset iout_oc_fault_limit mfr_date mfr_id mfr_location mfr_model mfr_revision mfr_serial name ot_fault_limit ot_warn_limit temperature1 temperature2 vin vin_ov_fault_limit vin_uv_fault_limit vout vout_mode vout_n vout_ov_fault_limit vout_uv_fault_limit iom.gpio0={SUCCESS=1454} iom.gpio1={SUCCESS=1460} iom.gpio2={SUCCESS=1454} iom.gpio3={SUCCESS=2974} iom.temp.inlet1={SUCCESS=5515} iom.temp.inlet2={SUCCESS=5515} iom.temp.woodside={SUCCESS=4826} c.fru={SUCCESS=1} c.seeprom={SUCCESS=76} f.fm0.fc={SUCCESS=6040} f.fm0.fru={SUCCESS=1} f.fm1.fc={SUCCESS=6039} f.fm1.fru={SUCCESS=1} f.fm2.fc={SUCCESS=6039} f.fm2.fru={SUCCESS=1} f.fm3.fc={SUCCESS=6039} f.fm3.fru={SUCCESS=1} f.fm4.fc={SUCCESS=6041} f.fm4.fru={SUCCESS=1} f.fm5.fc={SUCCESS=6039} f.fm5.fru={SUCCESS=1} f.fm6.fc={SUCCESS=6039} f.fm6.fru={SUCCESS=1} f.fm7.fc={SUCCESS=6039} f.fm7.fru={SUCCESS=1} p.psu3.psmi={SUCCESS=18732} p.psu0.fru={SUCCESS=4} p.psu0.psmi={SUCCESS=18791} p.psu1.fru={SUCCESS=4} p.psu1.psmi={SUCCESS=18760} p.psu2.fru={SUCCESS=4} p.psu2.psmi={SUCCESS=18791} p.psu3.fru={SUCCESS=4} c.gpio0={ENXIO=8} c.gpio1={ENXIO=8} c.gpio2={ENXIO=8} c.gpio3={ENXIO=8} # I2C Driver sysctl entries sysctl: error: permission denied on key 'net.ipv4.route.flush' sysctl: error: permission denied on key 'kernel.cad_pid' sysctl: error: permission denied on key 'kernel.cap-bound' dev.i2c.disconnect_retry = 3 dev.i2c.post_trigger = 64 dev.i2c.norxack_blink = 5 dev.i2c.norxack_blink = 5 dev.i2c.fixup_blink = 0 dev.i2c.pca9541-workaround = 16 dev.i2c.wait_deadline = 30 dev.i2c.chassis_reservation.demand = 0 dev.i2c.chassis_reservation.lock_state = 1 dev.i2c.chassis_reservation.auto_release = 1 dev.i2c.chassis_reservation.on_demand = 0 dev.i2c.chassis_reservation.pause_gilroy_thread = 0 dev.i2c.chassis_reservation.min_notheld_ms = 150 dev.i2c.chassis_reservation.wait_extra_ms = 3000 dev.i2c.chassis_reservation.grace_ms = 750 dev.i2c.chassis_reservation.hold_ms = 1500 dev.i2c.chassis_reservation.wait_ms = 4500 dev.i2c.gilroy-debug-level = 3 dev.i2c.debug-level = 1 dev.i2c.pca9541-businit = 1 dev.i2c.pca9541-delay = 250 dev.i2c.bus2.write-cdelay = 100 dev.i2c.bus2.write-delay = 100 dev.i2c.bus1.write-cdelay = 30 dev.i2c.bus1.write-delay = 30
... View more
Created by
Richard Simmons
in Unified Computing System Discussions
in Unified Computing System Discussions
05-04-2017
08:26 AM
05-04-2017
08:26 AM
I'll see if i can get a case raised for this tomorrow, in the mean time is there any troubleshooting i can look into myself for this?
Thanks,
Richard
... View more
05-04-2017
05:42 AM
Hi Kirk,
Thanks for getting back so promptly, i will certainly test this tomorrow - the Chassis has been fully powered down since the update. I will let you know tomorrow how it goes.
Thanks,
Richard
... View more
Created by
Richard Simmons
in Unified Computing System Discussions
in Unified Computing System Discussions
05-04-2017
12:59 AM
05-04-2017
12:59 AM
Hi,
Recently upgrade our test Fabric Interconnects and 5108 Chassis to 3.1(2e) and since this the 5108 Chassis fan's have all been running at full speed (9372).
I can see there are bugs for other versions for fan speed but can't find one for this version, does anyone know the bug ID or a fix to reduce the fan speed?
Thanks,
Richard
... View more
- Tags:
- #ucs #5108 #fan
Labels:
12-09-2016
06:41 AM
Hi Andy,
I'm surprised that they allow you to do that, basically letting you spoof calls from any number - I would spend some time on validating this first to see if they do actually allow it.
I assume the use case for this is CFA or CFNA configured on a DN?
Under System > Service Parameters > Call Manager - you could try setting Retain Forward Information Required Field to True
Regards,
Richard
... View more
12-09-2016
05:56 AM
Hi Andy,
From the sounds of it you are trying to hairpin a call on the Gateway, i.e External call comes in and then goes back out. Typically most providers only allow you to present a CLI number which is on the circuit range or other non-geographic numbers that you may own.
So even if you were to present the original callers number as the calling party to the gateway, whether that be a mobile or landline, I suspect the carrier would override it with either the circuit default or block the CLI.
You can check this by setting the External Phone Number Mask on your line as a different number, monitor the gateway to see what number is sent and then see what is presented as CLI
Regards,
Richard
... View more
12-09-2016
02:59 AM
Hi,
From the look of the call flow diagram attached you could achieve the same without adding another menu, simply add options 6 & 7 to the Main Menu but don't update the prompt and tell the users that need to know about this.
Hope this helps,
Richard
... View more
Created by
Richard Simmons
in Unified Computing System Discussions
in Unified Computing System Discussions
11-28-2016
11:35 AM
11-28-2016
11:35 AM
Thanks Kirk, raised a TAC case and it required hardware replacement .
Regards,
Richard
... View more
03-27-2020
CUCM: 12.0CUBE: 15.5(3)S4b Internal Jabber to Jabber calling works fine,
can place a call on hold an...
Created by
Richard Simmons
in TelePresence and Video Infrastructure
02-07-2020
02-07-2020
Thanks Anthony, great post!
01-27-2020
missed your comment on setting the translation-profile outgoing - once
i'd done that it works fine -...
01-27-2020
I tried adding a dial-peer with the loopback address and get the
following error; %CALL_CONTROL-6-CA...
01-24-2020
Hi, I have a group of phones that register in SRST, the phones DN's do
not match the DDI's, as such ...
Created by
Richard Simmons
in IP Telephony and Phones
01-23-2020
01-23-2020
I found the fix for this, i hadn't populated the SIP address within the
SRST reference on CUCM, once...
Created by
Richard Simmons
in IP Telephony and Phones
01-22-2020
01-22-2020
when you say chose mode east - is that auto correct from mode esrst ? is
it not possible just to use...
Created by
Richard Simmons
in IP Telephony and Phones
01-22-2020
01-22-2020
Hi All, Having an issue getting 7841 phones to register to a 4431 router
in SRST, none of my phones ...
Created by
Richard Simmons
in Collaboration Applications
11-19-2019
11-19-2019
It is possible to disable to the toaster notification and you can do
this via the jabber-config.xml ...
Created by
Richard Simmons
in Collaboration Applications
11-15-2019
11-15-2019
Were you able to find out how to disable the call toaster notification
without doing it manually on ...
Created by
Richard Simmons
in Unified Communications Infrastructure
01-10-2018
01-10-2018
Do you get this resolved? I am looking into the same issue at the
moment.
08-15-2017
Hi Slavik, It sounds like you've got working exactly the scenario that
i'm looking into, 3 CUCM clus...
05-16-2017
Hi, bit late to the party on this one but i've just run into this issue.
I have associated all of th...
Public Statistics
| Date Registered | 12-18-2008 08:45 AM |
| Date Last Visited | 03-27-2020 03:16 AM |
| Total Messages Posted | 253 |
| Total Helpful Votes Received | 132 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 10 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "VIP Advisor"){kind=icon}
Helpful Votes From
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
