Cisco Community
English
Register
New community login process starting July 13 - LEARN MORE HERE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
rogelioalvez
‎04-08-2020
Beginner
Recent Badges
Awards
Recent Badges
See all
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
10 Replies
5 Replies
custom.cisco.stats.title
Member since ‎01-13-2005
157
Posts
10
Helpful
0
Solutions

Re: Meaning of the output in the "show ip bgp <prefix> <mask>" command

Created by in Routing
04-06-2020
04-06-2020
Thanks for clearing this up! Best regards, Rogelio 

Meaning of the output in the "show ip bgp <prefix> <mask>" command

Created by in Routing
04-06-2020
04-06-2020
Hello team:I have the following output in my Cisco router to the "show ip bgp 172.25.159.140 255.255...

Re: Nested output service-policy on tunnel (GRE) interface

Created by in Other Network Architecture Subjects
03-25-2020
03-25-2020
You were right! I executed these same commands on another router model (it was easier than an IOS up...

Re: Nested output service-policy on tunnel (GRE) interface

Created by in Other Network Architecture Subjects
03-25-2020
03-25-2020
Hello Cristian:I will look for a different version and let you know what happened. Thanks!

Nested output service-policy on tunnel (GRE) interface

Created by in Other Network Architecture Subjects
03-25-2020
03-25-2020
Hello team:I want to apply a basic output policy to a tunnel (GRE) interface, like the following:pol...

Hi Jon:

Created by in Switching
01-29-2016
01-29-2016
Hi Jon: The remaining 10GE ports on both sides are idle. And there are many high-end servers connect...

2x10GE Portchannel on a CAT4900M with 8x10GE (2:1) card does not exceed 10GE of througput

Created by in Switching
01-29-2016
01-29-2016
Hello team: We have a 2x10GE (layer3) portchannel established between a ASR1006 and a CAT4900M. The ...

Hi Oscar:I am sorry. I gave

Created by in Network Management
03-28-2014
03-28-2014
Hi Oscar:I am sorry. I gave up on this without any solution to the issue.regards, Rogelio

CAT6500 VSS Dual-active detection fast-hello: ¿both endpoints?

Created by in Switching
08-17-2013
08-17-2013
Hello team:The config guide says that you must choose and configure at least one interface (max of 4...

Re:Configure IP SLA to generate syslog messages

Created by in Network Management
05-27-2013
05-27-2013
Hi Sochi:Thank you very much for answer, and I apologize for my late answer. I have been 5 days with...

Configure IP SLA to generate syslog messages

Created by in Network Management
05-23-2013
05-23-2013
Hello Hitesh:My name is Rogelio; I am a technician located in Argentina. I am experiencing quite the...

I can not make IP SLA to signal SNMP traps upon timeout

Created by in Network Management
05-23-2013
05-23-2013
Team:I could make the router send a SYSLOG message notifying the timeout condition, but only ONCE. ¿...

I can not make IP SLA to signal SNMP traps upon timeout

Created by in Network Management
05-22-2013
05-22-2013
Just for the record.I added the following commandip sla monitor reaction-configuration 1 react timeo...

I can not make IP SLA to signal SNMP traps upon timeout

Created by in Network Management
05-22-2013
05-22-2013
Hello team.I want SNMP traps to be sent every time an IP SLA (ICMP) object times out. For that purpo...

Re: PBR on contents AND next-hop of incoming packets?

Created by in Switching
05-21-2013
05-21-2013
Thank you very much again. I will follow this advice.regards, Rogelio
Public Statistics
Date Registered ‎01-13-2005 12:43 AM
Date Last Visited ‎04-08-2020 06:01 AM
Total Messages Posted 157
Total Helpful Votes Received 10
Helpful Votes Given To
Helpful Votes From
See all >