Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About end2endtechs
08-15-2019
Stats
Member since
05-05-2007
11
Posts
0
Helpful
0
Solutions
10-06-2016
09:46 PM
Hello ,
Thanks for your reply. I was able to see that too after some search. Can you please verify on your end the impact of exposing any of the above equipment to temp around
130-135 degrees F (57-60 C) for four hours
... View more
Created by
end2endtechs
in Network Management
in Network Management
10-06-2016
07:17 PM
10-06-2016
07:17 PM
Hello,
I want to know what is the maximum temperature endurance for Cisco equipment listed below :
Cisco Routers – 2911, 1811
Cisco Catalyst WS-C2960S-48FPS-L
Cisco IP Phones - CP-7925G, CP-7945G, CP-7965G
Thank you,
Sam
... View more
Labels:
Created by
end2endtechs
in IP Telephony and Phones
in IP Telephony and Phones
06-07-2015
06:26 PM
06-07-2015
06:26 PM
Did you ever find a solution to this?
... View more
12-06-2013
09:34 PM
For AnyConnect users, the following user error message is seen: "Connection attempt has failed due to server communication errors. Please retry the connection" The AnyConnect event log will show the following error message snippet: Function: ConnectIfc::connect Invoked Function: ConnectIfc::handleRedirects Description: CONNECTIFC_ERROR_HTTP_MAX_ REDIRS_EXCEEDED Cisco Is still finding answers and there is no fix for it yet
... View more
Created by
end2endtechs
in IP Telephony and Phones
in IP Telephony and Phones
08-01-2012
02:20 PM
08-01-2012
02:20 PM
Hi, I have a CME, with SIP and SCCP phones (8961, 6921 and 7961). I am able to transfer a call to a user’s voicemail using any SCCP phone, but when I try from a SIP phone the other person on the line just hear dead air. I have tested it internally and externally, the same. I also get dead air when it get transferred to AA. Any Idea????? Thank you
... View more
Labels:
10-07-2010
12:57 PM
Thanks for the response Chad. I had the monitor session setup, but I was only monitoring one access interface on one of my switches. There was just a PC on the port as I was just in test mode. No real heavy traffic being generated or anything.
... View more
10-06-2010
07:19 AM
Hi all, I've got three switches, let's call them A, B, and C. I've created vlan 99 on each switch and configured vlan 99 as remote-span. When I add vlan 99 to my trunk ports, at some point, DHCP traffic (and possibly other broadcast traffic) stops working. When I remove vlan 99 from the trunk ports, DHCP works again. Adding vlan 99 again does not break things immediately though. So things look like so: A (RSPAN source) -> B -> C (RSPAN destination) The trunk ports carry all sorts of production VLANs on them, as well as the RSPAN VLAN. Switch A is a 2960 Switch B is a 3560 Switch C is a 2960 All switches are running 12.2(53)SE2 I've now taken down two networks because of this strange behavior. It seems to all be working fine in my testing, but at some point into production, certain types of traffic stop working. DHCP is the easiest example for testing and capturing. Has anybody run into this? I've searched around and was unable to find anything on this. Any help would be appreciated. Thanks!
... View more
Labels:
Created by
end2endtechs
in IP Telephony and Phones
in IP Telephony and Phones
12-09-2009
10:54 AM
12-09-2009
10:54 AM
Thanks for the reply, this helps alot. I think I should just stay on version 7.0 for now.
... View more
Created by
end2endtechs
in IP Telephony and Phones
in IP Telephony and Phones
12-04-2009
09:15 AM
12-04-2009
09:15 AM
I have a 2851 that I need to upgrade and I'm looking at putting CME 8.0 on it, but have not been able to find a document that states whether there is a compatible version of CUE that can be installed on the Integrated Service Engine. Has anyone been able to try this, or have a link to a document that states compatibility?
... View more
Labels:
Created by
end2endtechs
in Other Security Subjects
in Other Security Subjects
05-27-2009
05:44 AM
05-27-2009
05:44 AM
MARS 6.0.1 RADIUS - IAS I've configured AAA in MARS and it works when I test it. When I log out and back in to the GUI with my RADIUS credentials. MARS doesn't seem to even try to send the authentication request to the RADIUS server and I get a "login failure" error. Any thoughts? Thanks
... View more
Labels:
10-06-2016
Hello , Thanks for your reply. I was able to see that too after some
search. Can you please verify o...
Created by
end2endtechs
in Network Management
10-06-2016
10-06-2016
Hello, I want to know what is the maximum temperature endurance for
Cisco equipment listed below : C...
12-06-2013
For AnyConnect users, the following user error message is
seen:"Connection attempt has failed due to...
Created by
end2endtechs
in IP Telephony and Phones
08-01-2012
08-01-2012
Hi,I have a CME, with SIP and SCCP phones (8961, 6921 and 7961). I am
able to transfer a call to a u...
10-07-2010
Thanks for the response Chad. I had the monitor session setup, but I was
only monitoring one access ...
10-06-2010
Hi all,I've got three switches, let's call them A, B, and C. I've
created vlan 99 on each switch and...
Created by
end2endtechs
in IP Telephony and Phones
12-09-2009
12-09-2009
Thanks for the reply, this helps alot. I think I should just stay on
version 7.0 for now.
Created by
end2endtechs
in IP Telephony and Phones
12-04-2009
12-04-2009
I have a 2851 that I need to upgrade and I'm looking at putting CME 8.0
on it, but have not been abl...
Created by
end2endtechs
in Other Security Subjects
05-27-2009
05-27-2009
MARS 6.0.1RADIUS - IASI've configured AAA in MARS and it works when I
test it. When I log out and ba...
Public Statistics
| Date Registered | 05-05-2007 09:55 PM |
| Date Last Visited | 08-15-2019 11:36 PM |
| Total Messages Posted | 11 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "VIP Mentor"){kind=icon}
