Hi Pal, I want to ask if anybody ever got the same issue like me as this follow? ES-N1KV# sh mod Mod  Ports  Module-Type                       Model               Status ---  -----  --------------------------------  ------------------  ------------ 1    0      Virtual Supervisor Module         Nexus1000V          ha-standby 2    0      Virtual Supervisor Module         Nexus1000V          active * 10   248    Virtual Ethernet Module           NA                  unlicensed 20   248    Virtual Ethernet Module           NA                  unlicensed I have private vlan feature activated but I can't even communicate in the same community. Does licensing probably be the issue? I'm using N1Kv version 4.2(1)SV2(1.1) Thanks in advanced. Edwin ... View more

Hi, I want to ask about netflow for N7K. When I use netflow version 9 in N7K to forward traffic to netflow server, the netflow server detects all interfaces in N7K with ifindex. I can mapping the ifindex interface in netflow server with command "show interface snmp-ifindex" in N7K. But, If I use netflow version 5 in N7K to forward traffic to netflow server, the netflow server detects all interfaces int N7K with different ifindex format with version 9. So, I can't mapping the ifindex interface in netflow server. Does anyone know how to map ifindex interface in N7K with netflow version 5? Thank you so much. ... View more

Guys, Have you ever found the problem that if I set two tacacs server in my N7K and the primary tacacs server fail, won't switch over to another tacacs server. Thank you. ... View more

Sorry admin. this case is resolved just now. You can delete this thread. Sorry for the bothering. ... View more

Dear Guys, I have 2 VSM. One as the primary VSM, and the other as the secondary VSM. When I switched over the primary VSM to the secondary VSM, all the VEM modules including the primary VSM module aren't detected. Do you know what is the root cause? What should I do to solve this problem? Thanks before. Edwin ... View more

Guys, I have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. This is the output of show version: Cisco IOS Software, 7200 Software (C7200P-ADVSECURITYK9-M), Version 12.4(4)XD11, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Fri 03-Oct-08 15:52 by ccai ROM: System Bootstrap, Version 12.4(4r)XD5, RELEASE SOFTWARE (fc1) BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(4)XD2, RELEASE SOFTWARE (fc2) JKTPZBIIT1-6-WAN02-7206 uptime is 4 hours, 39 minutes System returned to ROM by error - a SegV exception, PC 0x1E9ADA8 at 11:06:00 IND Thu Mar 17 2011 System restarted at 11:07:41 IND Thu Mar 17 2011 System image file is "disk2:/c7200p-advsecurityk9-mz.124-4.XD11.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com . Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 35461839 MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.1 6 slot VXR midplane, Version 2.11 Last reset from power-on PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points. Current configuration on bus mb1 has a total of 0 bandwidth points. This configuration is within the PCI bus capacity and is supported. PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points. Current configuration on bus mb2 has a total of 400 bandwidth points. This configuration is within the PCI bus capacity and is supported. Please refer to the following document "Cisco 7200 Series Port Adaptor Hardware Configuration Guidelines" on Cisco.com < http://www.cisco.com > for c7200 bandwidth points oversubscription and usage guidelines. C7200 PA Jacket Card present in I/O slot (VAM2+ Encryption/Compression engine,) 3 FastEthernet interfaces 3 Gigabit Ethernet interfaces 16 Serial interfaces 1 Virtual Private Network (VPN) Module 2045K bytes of NVRAM. 250880K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes). 65536K bytes of Flash internal SIMM (Sector size 512K). Configuration register is 0x2102 I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?                              CSCtj21237               Unexpected reboot due to SegV Exception                                                                 Info                                                                                                              Open                   2  Thanks for your help. Edwin ... View more

Dear fellows, I have installed 4 unit Cisco Aironet 1250 acting as Autonomous AP each. I want to integrate these AP to Windows Active Directory for authentication level. When I read configuration guide on Cisco Aironet, they must be authenticated via RADIUS server. Is it possible that these AP directly authenticated to Active Directory via LDAP protocol? Is there any supporting documents? Thank you. Edwin ... View more