About 4rmorris

4rmorris · 09-09-2018

Hi all, I've got a Cisco 2811 router running 15.1.4 with an SDM configured ZBFW. Behind it there are ATAs connecting phones to a cloud-based VoIP service provider. So no CUCM or CME on the router, just pass-through SIP registrations to the SP and t...

4rmorris · 02-14-2014

Hi all,I've got a production implementation of CUCM 9.1.2. We don't currently do any SIP URI dialing, but I'm starting to investigate this.Our email addresses in LDAP (MS AD) are in the Mail field. By default, CUCM points the Directory URI field in...

4rmorris · 06-05-2013

Hi all,We're in the process of migrating our phones from CUCM 6.1.5 to CUCM 9.1.1. One of our key steps is to change Option 150 in our DHCP server and then reset the phones. In our pilot office of 200 phones, 95% of phones reset, found the new serv...

4rmorris · 06-03-2013

Hi all,We recently upgraded to version 9.1.1 of Unity Connection from 8.0. Specifically, version 9.1.1.10000-32.I was asked a question regarding outside callers getting warning about full mailboxes for my users, and went to double check that the opt...

4rmorris · 05-28-2009

Hi there,Appreciate if anyone has any permanent solution for this. We have a deployment of 7965G and 7975G IP phones along with a number of Plantronics CS-50 & CS-55 headsets. We're using the Plantronics APC-4 Headset Hookswitch Control (HHC) adapt...

4rmorris · 10-02-2014

Hi Val,It depends where your C40 is registered. If it's registered to the Expressway-C then you need a SIP trunk between CUCM and Expressway-C and dial plan in both to route the calls. If it's registered to CUCM directly, the CUCM dial plan will ma...

4rmorris · 10-01-2014

Hi there,As of Jabber for iOS and Android v10.5, which released on Sept. 15th, you can now use phone only mode on mobile devices. I'm not sure if it will register in phone only mode via the VCS-E, you might need a VPN connection on the mobile device...

4rmorris · 07-04-2014

This post (and all the Cisco docs I could find) neglect to mention that any firewall or IPS software running on the PC (like Symantec or Mcafee) needs to be configured to allow UDP port 5070 in and out of the PC. I followed all the instructions, but...

4rmorris · 03-07-2014

I'm using Jabber for Windows version 9.6. I'm set up in phone only mode, but it should work in UC mode too, if you have a presence server (I don't).The Directory URIs end up in their own partition called (maybe obviously) Directory URI  I just added...

4rmorris · 03-04-2014

Hi Christian,We did this in our production environment on the weekend and no issues at all. I tested with Jabber for Windows and I can place calls by URI now (just needed to add the Directory URI partition to my CSS).Really appreciate all the great f...

Member Since	‎01-10-2005 12:52 PM
Date Last Visited	‎01-14-2021 09:56 PM
Posts	122
Total Helpful Votes Received	100

User Statistics

User Activity

iOS Zone Based Firewall (ZBFW) drops SIP calls after 20 minutes

Changing LDAP Directory URI field mapping after installation

Some 7965 & 7975 phones do not refresh TFTP server upon Option 150 change in DHCP server

Unity Connection 9.1.1 - Full Mailbox Check For Outside Callers option disappeared

Wireless Headset Problems with Plantronics APC-4 HHC adapter

Hi Val,It depends where your

Hi there,As of Jabber for iOS

This post (and all the Cisco

Re:Changing LDAP Directory URI field mapping after installation

Re:Changing LDAP Directory URI field mapping after installation