Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About divine007
01-09-2019
Stats
Member since
03-03-2010
168
Posts
0
Helpful
0
Solutions
11-12-2015
07:55 AM
The 2 phones is just an example
i have more than 20 phones ranging from 7911 to 7975
There is o special config
... View more
Created by
divine007
in IP Telephony and Phones
in IP Telephony and Phones
11-12-2015
06:59 AM
11-12-2015
06:59 AM
Greetings
I have my cisco phones on a 2811 calling same number simultaneously
Thats 251 calling 251 and 201 calling 201
How can i solve this problem
... View more
Labels:
10-02-2015
03:29 AM
isdn switch-type primary-net5 ! ! voice service voip allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip h323 no call service stop sip ! ! voice translation-rule 5 rule 1 /5077/ /2001/ ! voice translation-profile INCOMING-CALLS-New translate called 5 ! voice-card 0 ! controller E1 0/1/0 clock source internal pri-group timeslots 1-31 ! interface Serial0/1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice isdn bchan-number-order ascending isdn sending-complete no cdp enable ! voice-port 0/1/0:15 ! dial-peer voice 5080 voip description IVR destination-pattern 2001 session protocol sipv2 session target ipv4:192.168.10.1 dtmf-relay rtp-nte codec g711ulaw ! dial-peer voice 5077 pots description "From GSM" translation-profile incoming INCOMING-CALLS-New incoming called-number 5077 direct-inward-dial ! !
... View more
10-01-2015
04:00 AM
is a PRI interface Serial0/1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice isdn bchan-number-order ascending isdn sending-complete no cdp enable ! dial-peer voice 5077 pots description "incoming Calls from CAMTEL-MTN-ORANGE' translation-profile incoming INCOMING-CALLS-New incoming called-number 5077 direct-inward-dial
... View more
09-30-2015
09:07 AM
I have a Cisco 2911 i have conf with pstn provider did translation and created a trunk sip an sent extension to IVR server but from GSM number when i dial the ivr number it drops like after 8 or more seconds but when i call directly from a cisco ip phone it passes with no drops what could be there cause for this
... View more
Labels:
09-13-2015
11:30 PM
Hi Manish, I understand that But am talking about the function behind. Because even you record an say "please do enter the extension of the user you which to reach" and function is not configured behind when you enter the number you will get an error message or the system won't recognise the operation. So I have a problem of configuring that function behind so that when the extension is entered the call should be sent to that extension. Thanks
... View more
Created by
divine007
in Other Collaboration Subjects
in Other Collaboration Subjects
09-13-2015
08:41 AM
09-13-2015
08:41 AM
Hey I need to configure CUC in such a way that when someone calls instead of calling the persons name (directory handler) I need to instead input but the persons number for the calls to initiated
... View more
Labels:
09-11-2015
06:16 AM
Thanks a lot it worked perfectly your wiki doc. I have just one last issue instead calling the users name so that calls be forwarded I want to instead ask but for the user extension to be input how cN this be achieve. Thanks
... View more
Created by
divine007
in Other Collaboration Subjects
in Other Collaboration Subjects
09-10-2015
11:18 AM
09-10-2015
11:18 AM
Thanks for the wiki I will go through it and let you know the outcome.
... View more
09-10-2015
09:35 AM
Is not registered it's showing status unknown I want to do call handler (auto attendant) Between CUCM 8.5 and CUC 8.5 I get but only voice message calls not transfered to operator number or assign number Am lost in the ocean
... View more
Created by
divine007
in Other Collaboration Subjects
in Other Collaboration Subjects
09-10-2015
04:08 AM
09-10-2015
04:08 AM
Greetings I have setup my CUCM and CUC under the system call handler am using extension 5605 i have applied that to cti route point but the status is showing unknown seems as if am missing something which i can't detect what could that be. Thanks
... View more
Labels:
09-10-2015
12:08 AM
Terry I mean under system call handler when I click under edit am suppose to have options to edit but the edit tab is not responding nor options shown
... View more
11-12-2015
The 2 phones is just an example i have more than 20 phones ranging from
7911 to 7975 There is o spec...
11-12-2015
Greetings I have my cisco phones on a 2811 calling same number
simultaneously Thats 251 calling 251 ...
10-02-2015
isdn switch-type primary-net5!!voice service voip allow-connections h323
to sip allow-connections si...
10-01-2015
is a PRI interface Serial0/1/0:15 no ip address encapsulation hdlc isdn
switch-type primary-net5 isd...
09-30-2015
I have a Cisco 2911 i have conf with pstn provider did translation and
created a trunk sip an sent e...
09-16-2015
Your right option 1 now it works fineI have configured call handler
where i enter the local extensio...
Created by
divine007
in Unified Communications Infrastructure
09-15-2015
09-15-2015
Greetings I configured call handler as call_ext with its number. But
when I try to call I hear "User...
09-14-2015
So if i just configure my system call handler and don't configure any
call inputswhen some calls he ...
Created by
divine007
in Unified Communications Infrastructure
09-14-2015
09-14-2015
I have configured my system call handler for a small hotline service is
ok But now i did another con...
09-13-2015
Hi Manish, I understand thatBut am talking about the function behind.
Because even you record an say...
Public Statistics
| Date Registered | 03-03-2010 07:00 AM |
| Date Last Visited | 01-09-2019 12:05 AM |
| Total Messages Posted | 168 |
.jpg "Hall of Fame Master"){kind=icon}
