Hello, I have MCS-7845-I3 on which I have configured RAID 1 after CTRL+H option. Once done wite the RAID configuration we installed windows 2003 server which also got installed succesfully. But when I reboot the system after OS installation then it fails, I am not sure which option to select in Boot Manager. Unlike UCS C Series there is no option for "LSI Mega Raid Adapter" in the boot options. Regards, Amritesh Anand ... View more

Hi, I have few queries with respect to CUCILync 9.2, after the succesfull integration I have following doubts. 1. Does it only show presence information on CUCILync client or Lync client as well. 2. Can I not make calls using Lync Client, or it is only through CUCILync client. 3. Call history only available on CUCILync client not on Lync client. 4.  Instant Messaging Predictive search only on CUCILync client I have also attached the test report. Is this the way CUCILync 9.2 behaves or we are missing anything in the integration to make it function correctly. Please suggest. Regards, Amritesh Anand ... View more

Hi, I am preparing a BOM for Cisco UC Envoirnement for 1000 users. Customer also need Mobile clients for iphone, Blackberry, Nokia and Anderoid phones. I have prepared a BOM for CUWL-PRO with soft client option of all the above mobile clients. Do we also need Cisco ASA proxy for that when outside the company wifi network. Please suggest. Regards, Anand                 ... View more

Hi, I have a CUP server 8 and CUCM 8.0.3, CUPC is 8.5. The issue is that everything works fine in softphone mode but no video on Deskphone mode. My deskphone is 6921 and is directly connected to the Phone, Firewall is off and Video is enabled in the Phone settings Regards AA ... View more

Hi, SNR configuration works perfectly fine but it is not working when the user is logged out. I am not even sure if this is supposed to work. Regards, Amritesh Anand ... View more

Hi, Branch Router is able Multicast MOH with PSTN phones but not working between IP Phones. I am enclosing the config below which I have at the brach location. ip multicast-routing int vlan 300 description voice vlan ip pim dense-mode call-manager fallback-mgcp ccm-manager musin-on-hold call-manager-fallback ip source-address 192.168.10.1 port 2000 max-ephone 20 max-dn 40 dual-line moh music-on-hold.au multicast moh 239.1.1.1 port 16384 Loopbak IP and then VLAN IP Regards, Amritesh Anand ... View more

Hi, I have CUE integrated with CUCM at remote location. Everything works fine when WAN is up but in SRST mode the call do not get forwarded to the CUE. I have the below mentioned config done in the SRST mode. SRST config dial-peer voice 3050  voip destination-pattern 3050 description Cisco Unity Express voicemail pilot number session protocol sipv2 session target ipv4:142.102.66.253 dtmf-relay sip-notify codec g711ulaw no vad call-manager-fallback max-conferences 8 gain -6 transfer-system full-consult ip source-address 142.102.66.1 port 2000 max-ephones 10 max-dn 5 dual-line voicemail 3050 call-forward pattern .T call-forward busy 3050 call-forward noan 3050 timeout 10 mwi relay time-zone 42 sip-ua mwi-server ipv4:142.102.66.253 expires 3600 port 5060 transport udp ___________ CUE config ___________ ccn subsystem sip gateway address "142.102.66.1" gateway port 5060 mwi sip sub-notify end subsystem Please suggest. I also have SIP Triggered configured for the same. ... View more