About davetechfreak

davetechfreak · 08-18-2016

Hi, Has anyone got much experience with Cisco ASR NIM-SSD drives? I am looking at whether if it's possible to just buy a NIM-SSD (http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001-x/asr1hig/asr1_hw2.html#62379) carrier card and...

davetechfreak · 01-30-2015

Hi, I am trying to create an EEM "Port-knocking" script which should act upon an ordered sequence of SYSLOG messages. The SYSLOG messages are generated by some "deny tcp any any XXX log STRING" ACLs, applied to the outside interface. Here is what I ...

davetechfreak · 01-10-2014

Hiya,I have an Any Connect WebVpn (ssl vpn?) set up on an IOS 15.2(4)M4. My current WebVPN is set up for Cisco Phones to use SSL VPN to connect to a Cisco Call Manager (CUCM 9.x). I also tried connecting with an Any Connect client from a PC and it se...

davetechfreak · 11-14-2013

Hello,I am trying to figure out why we cannot forward calls on a SIP trunk. Inbound and Outbound calls work fine, it is only when we try to forward a call (i.e. CfwdAll from a phone attached to CUCM) that it fails...Current setup includes a CUCM 9, C...

davetechfreak · 08-02-2013

Hi,I am having a problem with a Cisco 7937 on a UC540 with an 8.6.1 software pack. Basically, the phone never registers and keeps rebooting all the time. I think this is the same issue as in these two threads: https://supportforums.cisco.com/thread/2...

davetechfreak · 11-16-2013

Hi Just an idea... I f you have CUC you can route the call to a System Call Handler and apply a schedule to it so that during normal working hours it only rings onto the attendant's phone. Then during out-of-hours you can configure it to transfer to ...

davetechfreak · 11-16-2013

Hi mate, I managed to get it working. What I did was I stopped the transcoder on the gateway (did 'no sccp' and 'no telephony-service') and calls were fine after that. Although this gets it working I still cannot understand why it was failing with th...

davetechfreak · 11-15-2013

Hello and thanks for helping us out! As you suggested the codec specification was missing under the dial-peer. Although calls are getting established now, I am stumbled upon another issue which I suspect is from the same (codec mismatch) nature... No...

davetechfreak · 08-05-2013

That is what I was just wondering, as well. Let us know if you find anything.

davetechfreak · 08-05-2013

Yes, you could have problems if not using vlans, however, the scenario should work fine. Did you plug your generic switch into the Expansion port on the UC? If so, make sure you remove the trunk configuration from it as it won't be able to establish ...

Member Since	‎02-13-2013 12:00 PM
Date Last Visited	‎04-03-2019 01:48 PM
Posts	38
Total Helpful Votes Received	5

User Statistics

User Activity

Would Cisco ASR 1001-x work with a non-cisco SSD drive?

Cisco EEM script to detect a sequence of SYSLOG messages

AnyConnect (SSL VPN on IoS) - Connection stuck on Android

Call Forwarded calls fail on SIP Trunk

Cisco 7937G Keeps Rebooting on a UC540 8.6.1

Notify all phones when main number is ringing

Re: Call Forwarded calls fail on SIP Trunk

Re: Call Forwarded calls fail on SIP Trunk

BE6000 Migration program?

UC560 behind ASA + LAN connectivity