Hi Team,   We have 2 units of  UCS-FI-6332 ( UCS 6332 IRU Fabric Interconnect/32 QSFP+ports/8p Lic)  and MDS 9148. We are trying to configure FI interface as a FC port to connect with MDS but we are unable to configure FI port as a FC port. I think i am missing something in the configuration that enables FC port in the FI. Or is there a way to configure FCoE in the MDS?   Thank you ... View more

Hello Guys, I am deploying IPSec VPN over MPLS L3 ADSL link between HeadOffice and different branch locations. VPN tunnels are up and running i can successfully ping both sides. But the browsing is very very slow. Users at remote sites cannot browse the servers at headoffice as well as internet. I have tried following things: 1) Setting MTU in outside interface 2) Setting ip tcp adjust-mss in outside interface 3) Crypto ipsec df-bit clear (both locations) 3) Route-map clearing df-bit Still browsing is same. I cant figure out where the problem is? In my configuration or at ISP side?? Devices used for this configuration are: Head Office: Cisco C3945 Software (C3900-UNI​VERSALK9-M), Version 15.2(4)M3 Branch Office: Cisco C2911 Software (C2900-UNI​VERSALK9-M), Version 15.3(2)T I have attached configuration below: Thank you Sudan Dhakal ... View more

Hello Guys, I am trying to configure ADSL on 2911 with EHWIC VA-DSL-A card. PPPoE configuration is working fine but when i try to configure the ATM interface with static ip address i cant even ping my interface. I guess i am missing something. I am using pvc 0/35 for static and pvc 8/81 for pppoe. pppoe is working fine Details: Hardware: CISCO 2911/K9 Cisco IOS Software: C2900 Software (C2900-UNIVERSALK9-M), Version 15.3(2)T EHWIC-VA-DSL-A Configuration: ! controller VDSL 0/1/0 ! interface ATM0/1/0 no ip address no atm ilmi-keepalive ! interface ATM0/1/0.1 point-to-point ip address 172.18.1.105 255.255.255.252 pvc 0/35   protocol ip 172.18.1.105 broadcast   protocol ip 172.18.1.106 broadcast ! ! interface ATM0/1/0.2 point-to-point pvc 8/81   pppoe-client dial-pool-number 1 ! interface Ethernet0/1/0 no ip address shutdown ! interface Dialer0 ip address negotiated ip mtu 1452 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap pap callin ppp chap hostname adsl123456 ppp chap password 0 adsl123456 ppp pap sent-username adsl123456 password 0 adsl123456 ! Regards Sudan ... View more

          ---------------                                   ---------------          |   UC520   | ------------------------ |     861     |           ---------------                                   ---------------                  |                                                  |               LAN                                             LAN Scenario: UC520 box is at HQ and serving as a EZVPN server and 861 at branch as a EZVPN client. There is no problem with VPN i can communicate with HQ network. My ip phone get registered but facing these problems. 1) Dialling out and in OK 2) Connects OK after picking up 3) NO sound either way 4) Cannot end call from this side. End call button does not work 5) When other end hangs up - message "UCM down, features disabled". Then phone registers again. Identical symptoms for both softphone and 7941. ... View more

Hello Guys, I have configured my two vdsl link with ppp multilink but i am not getting the desired bandwidth. Here is my configuration is this okay or i need something more in the configuration. My router is 2921 what is the maximum WAN throughput of 2921? ! controller VDSL 0/0/0 ! controller VDSL 0/1/0 ! ! interface Multilink1 no ip address ip virtual-reassembly in ip virtual-reassembly out ppp multilink ppp multilink links maximum 4 ppp multilink group 1 ppp multilink fragment disable ppp multilink mrru local 1492 ppp multilink mrru remote 1492 waas enable ! interface Ethernet0/0/0 no ip address ! interface Ethernet0/0/0.10 encapsulation dot1Q 10 pppoe enable group global pppoe-client dial-pool-number 1 ! interface Ethernet0/1/0 no ip address ! interface Ethernet0/1/0.10 encapsulation dot1Q 10 pppoe enable group global pppoe-client dial-pool-number 1 ! interface Virtual-Template1 no ip address ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 ppp authentication pap callin ppp pap sent-username ******** password 0 ******** ppp multilink ppp timeout idle 2 ppp timeout multilink link remove 2 ! interface Dialer1 description line mtu 1492 no ip address ! ip route 0.0.0.0 0.0.0.0 Dialer0 ! ... View more