Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About zillah2004
Stats
Member since
12-30-2004
526
Posts
3
Helpful
0
Solutions
Created by
zillah2004
in Application Networking
in Application Networking
07-16-2018
04:06 PM
07-16-2018
04:06 PM
Dear Experts
Tried to search as below but couldn't find what i am looking for
https://www.google.com.au/search?q=Cisco+uBR10000+slots+/subslots+numbers&ei=YR9NW7PiMdLt0ATCqILgAw&start=10&sa=N&biw=1351&bih=594
I want to understand how uBR10000 slots numbers convention
https://imgur.com/a/LwzPC2B
https://imgur.com/a/ZP2mj8p
https://imgur.com/a/ItRdQVT
Attached photos showing we slots numbers start from 1 up to 8 ( right to left ) ,,,,we are supposed to call them slots ,,,,arn't we ?if so no drama
Third link showing "SUBSLOT 0" and "SUBSLOT 1" I would assume those are for 3 cards that were installed in slot 1 and slot 2 and slot 3 ,,,,is my assumption right ?
What are those numbers in the link below ?
https://imgur.com/a/ITMp2g6
How the naming convention would be ? Is it Slot /subslot /port number ???or something else ?
Thanks
... View more
Labels:
12-07-2017
03:25 PM
Dear folks
E1 that my sources of information all seem to concur on is that E1 can provide up to 2.048Mbps.
E1 has 32 time slots if all of them are used to carry data or voice then it makes since 32 TS x 64 kbps = 2.048 Mbps
But of course TS0 is reserved not to carry data or voice as TS0 is allocated entirely to frame alignment signal pattern, a remote alarm indication bit,,,,,etc.
TS16 reserved for CAS/CCS signalling in a voice environment, not in a data environment
Means we will end up 30 B channels of bandwidth for voice and 31 B channels for data ,,,,,,,,right ?
(Voice environment) TS0 and TS16 not to be used means we end up with 30 B channels x 64 kbps = can only achieve 1920 kbps. Say we add the 64 kbps D channel to that then still we miss our target and we only achieve 1984 kbps.
(Data environment) TS0 not to be used means we end up with 31 B channels x 64 = can only achieve 1984 kbps.
... View more
Labels:
Created by
zillah2004
in VPN and AnyConnect
in VPN and AnyConnect
11-15-2009
09:28 PM
11-15-2009
09:28 PM
>>3. Group Authentication -- This needs to match the headend configuration. On the headend there should be a group name defined for the VPN connections. The group contains the parameters for the VPN to connect such as which authentication servers to use, which policies, and which pre-shared-key. The pre-shared-key that you define in the group on the headend is what you use for the "password" for group authentication. << Thanks heater,,,,I do not have within netgear router what is called "Group Authentication" (to bundle policies, pre-shared-key, etc )please see the link below to have an idea what options I have got with FVS318 V3 http://www.scribd.com/doc/3800516/Netgear-FVS318-GreenBow-IPsec-VPN-Configuration for instance within Cisco VPN client under "Authentication Group" I have got username ,,,,,,,what would the cisco VPN's username match on the netgear router (compare to the link that I have posted) ? under "Authentication Group" I have got a password ,,,,,,,what would the cisco VPN's password match on the netgear router (compare to the link that I have posted)?
... View more
Created by
zillah2004
in VPN and AnyConnect
in VPN and AnyConnect
11-15-2009
05:01 PM
11-15-2009
05:01 PM
Hi I would like to use a Cisco VPN client with a Netgear FVS318 V3 ,,,,,I know how to configure Netgear FVS318 V3 for IPsec,,,because I am using TheGreenbow client now with it. But I do not know how to configure Cisco VPN (some client does not have TheGeenBow VPN utility) I just want to find out how to do that ? specially with the option "Group Authentication" which it asks about username and password. Thanks
... View more
Labels:
11-22-2007
08:52 PM
I have not designed this before , I am looking to make a proposal for a manufacture company is looking to implement IP VPN over MPLS for his/her customers (30 clients) what are the recommended requirements (router, leased line, etc,,,,) for each client to have ? Each customer site has got 10 users. Customer right now accessing customer site through ADSL connection (Internet) If we want to implement IP VPN MPLS , do we need to replace that ADSL connection with a leased line ? or still we can used ADSL connection ? or we have to have another connection aside from ADSL, (i.e. one connection is dedicated for IP VPN and the ADSL connection for accessing the internet ) If I am looking to use a Cisco router as Customer Edge router (CE router, because client right now does not have a Cisco router ) what type of router do I need ? what module should a router have ? , what type of ISO ? Do I need to have any other devices beside a Cisco router ? Regards
... View more
Labels:
11-22-2007
04:09 PM
Thnaks P What confusing me is : when I compared between the link from cisco http://www.cisco.com/en/US/products/hw/iad/ps497/products_installation_guide_chapter09186a008007e299.html and the link below : http://puck.nether.net/pipermail/cisco-nas/2003-December/000421.html In the link from cisco (Table C-7: EI Interface Cable Pinouts) uses 6 (while other uses 4) pinouts : Pin 8 --->1 Pin 15 --->9 Pin 7 --->2 Pin 9--->3 Pin 2 --->11 Pin 10 --->4 While in the other link uses 4 pintouts DB-15 ----- DB-15 1 ----- 3 3 ----- 1 9 ----- 11 11 ----- 9
... View more
11-22-2007
03:21 PM
Thanks P could you please tell which one of those links that I have posted can be used to make a DB15 to DB15 cable, because I can see they have been using different pinouts assignments
... View more
11-22-2007
01:54 PM
Thanks Scott >>The cable is easy: each end of the connector is one pair, with the pins being the top-most and bottom-most pins on either side (pins 1&9 and pins 8&15 ... crossover 1->8, 9->15). << Could you please refer me where have you found this ? and Are you talking about DB15 to DB15 ? because in the link that I have posted : http://puck.nether.net/pipermail/cisco-nas/2003-December/000421.html is different to what you have mentioned
... View more
11-20-2007
07:21 PM
Referring to my thread here http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Remote%20Access&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbe75cf I am looking to make DB15 to DB15 crossover cable to simulate ISDN E1 PRI. I found these two resources : http://puck.nether.net/pipermail/cisco-nas/2003-December/000421.html Table 4 http://www.cisco.com/en/US/products/hw/routers/ps332/products_installation_and_configuration_guide_chapter09186a00800e9ecb.html#35239 0r http://www.cisco.com/en/US/products/hw/iad/ps497/products_installation_guide_chapter09186a008007e299.html#xtocid7 Which one should I follow if I would like to make this type of cable ? Regards
... View more
Labels:
Created by
zillah2004
in VPN and AnyConnect
in VPN and AnyConnect
11-15-2007
02:02 PM
11-15-2007
02:02 PM
Why do we need to assign ip address to the D channel (signaling ) when we configure ISDN-PRI in the example below : http://www.cisco.com/univercd/cc/td/doc/product/access/ap/ap_ts3/ap_ts3sw/apswisd.htm <quote> Step 1:Specify the D channel of the first Primary Rate Interface (PRI): AS01(config)# interface Serial 0:23 AS01(config-if)# Step 2: Assign an IP address and subnet mask to the interface: AS01(config-if)# ip address 172.16.254.253 </quote> Regards
... View more
Labels:
11-14-2007
10:57 PM
The reason I am asking this question when I copied and pasted from a txt file to our router and issued a command show tech , I realized after while that 15 lines of ACLs entries were missing from the output of the show tech,,,,I do not why!!!!
... View more
11-14-2007
02:30 PM
>>Compare It << Do you mean this http://www.snapfiles.com/get/compareit.html Regards
... View more
11-14-2007
03:37 AM
We used to "copy and paste" configuration from a txt file. Sometimes I need to compare between the configuration's txt files and the output of the "show running-config" command. What is the recommended (powerful) text editor that can be used to compare between a configuration txt file and the output for "show running-config" command, specillay when we have got the configuartion file with too many lines of configurations. Regards Regards
... View more
Labels:
11-13-2007
10:38 PM
If I have got a router out of the box (does not have any configuration), to configure this router which configuration is recommended (better or advisable) , to copy a txt file via TFTP to the running-config, or copy and paste from txt to the terminal of the router ? Because there were an argue that : copy txt file via TFTP produces less error than copy and paste to a terminal. Note: ----- Please do not involve in the explanations of how to configure them. Regards
... View more
Labels:
Created by
zillah2004
in Application Networking
07-16-2018
07-16-2018
Dear Experts Tried to search as below but couldn't find what i am
looking for
https://www.google.com...
Created by
zillah2004
in Routing
12-07-2017
12-07-2017
Dear folks E1 that my sources of information all seem to concur on is
that E1 can provide up to 2.04...
Created by
zillah2004
in VPN and AnyConnect
11-15-2009
11-15-2009
>>3. Group Authentication -- This needs to match the headend
configuration. On the headend there sho...
11-15-2009
HiI would like to use a Cisco VPN client with a Netgear FVS318 V3 ,,,,,I
know how to configure Netge...
11-22-2007
I have not designed this before , I am looking to make a proposal for a
manufacture company is looki...
11-22-2007
Thnaks PWhat confusing me is : when I compared between the link from
ciscohttp://www.cisco.com/en/US...
11-22-2007
Thanks Pcould you please tell which one of those links that I have
posted can be used to make a DB15...
11-22-2007
Thanks Scott>>The cable is easy: each end of the connector is one pair,
with the pins being the top-...
11-20-2007
Referring to my thread
herehttp://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%...
Created by
zillah2004
in VPN and AnyConnect
11-15-2007
11-15-2007
Why do we need to assign ip address to the D channel (signaling ) when
we configure ISDN-PRI in the ...
Created by
zillah2004
in Switching
11-14-2007
11-14-2007
The reason I am asking this question when I copied and pasted from a txt
file to our router and issu...
Created by
zillah2004
in Switching
11-14-2007
11-14-2007
We used to "copy and paste" configuration from a txt file. Sometimes I
need to compare between the c...
Created by
zillah2004
in Switching
11-13-2007
11-13-2007
If I have got a router out of the box (does not have any configuration),
to configure this router wh...
Public Statistics
| Date Registered | 12-30-2004 09:51 PM |
| Date Last Visited | 07-27-2018 12:07 AM |
| Total Messages Posted | 526 |
| Total Helpful Votes Received | 3 |
Helpful Votes Given To
