About Hudaifa shakkir Nattukallingal

Hudaifa shakkir Nattukallingal · 05-22-2021

Hi, We have upgraded Cisco Dect base station 210 firmware to 4.8.1 (DBS-210-3PC_v0480_b0012). After the upgrade, we are unable to log in with the default admin account (admin/admin). We are able to log in with user account. Is there any changes in ne...

Hudaifa shakkir Nattukallingal · 10-12-2020

Hi Experts, I have SIP trunk to ISP and its registered and working. Every two minutes we are sending the REGISTER message, then we get SIP/2.0 401 Unauthorized, then sends the REGISTER with authorization string and gets 200 OK from ISP. This is norma...

Hudaifa shakkir Nattukallingal · 01-02-2017

Hi, Is it possible to make secure phone/jabber profile for encrypted communication without enabling mixed mode in cucm? We have currently cucm version 11.5. The reason for keeping the cucm to non-secure mode is , mixed mode cluster not supported by ...

Hudaifa shakkir Nattukallingal · 09-07-2016

Hi Team, Hi Have Cisco Prime Collaboration Assurance version 10.6 and need to integrate with LDAP using SSL. Normal connection without SSL (port 389) the test connection is successful. But using SSL, could not find how to import the certificate to t...

Hudaifa shakkir Nattukallingal · 06-05-2016

Hi, I have SIP trunk between Alcatel PBX and Cisco Callmanager. The calls are working in both direction. But when Alcatel extension made a call forward all to another Alcatel extension and call is made from Cisco the call is not working. I am getting...

Hudaifa shakkir Nattukallingal · 11-20-2022

Hi, You can restrict dialing the paging number by using partition and css. Create a separate partition for this paging number and assign to the required phone's css. Not sure if we can disable to speaker button so that user cannot disconnect it. than...

Hudaifa shakkir Nattukallingal · 05-05-2022

Hi,You can apply the sip-profiles either through the voice-class tenant or you can apply it globally under voice class voice -> under sip. This will be global, and the REGISTER message will take this profile. But the best approach is to go with tenan...

Hudaifa shakkir Nattukallingal · 04-20-2022

Hi,Is there any error message on display? You can follow the below set-up guide for the navigator. For the LAN connection did you try to put both codec and the navigator same vlan?https://www.cisco.com/c/en/us/support/docs/collaboration-endpoints/web...

Hudaifa shakkir Nattukallingal · 04-19-2022

Hi, Are you getting incoming calls,? is your SIP trunk is registered? Can you share the output of show sip-ua register status.Thanks

Hudaifa shakkir Nattukallingal · 04-18-2022

Hi Waqas. From the debug I can see that you are sending multiple INVITES to the service provider but there is no response. Please check the service provider.ThanksShakkir

Member Since	‎02-22-2009 01:03 AM
Date Last Visited	‎03-27-2024 12:16 AM
Posts	47
Total Helpful Votes Received	25

User Statistics

User Activity

Dect base 210 - Default credential

CUBE Re-Register message with Authorization header.

Secure phone/Jabber profile without mixed mode cluster

Cisco Prime Collaboration Assurance Secure LDAP access

Call forward not working // Cisco -->Alcatel(extA) --cfwall-->Alcatel(extB)

Re: Paging (InformaCast) With CUCM to restrict user to dial paging num

Re: CUBE, modify REGISTER Via address

Re: Navigator not connecting to device

Re: Calls are not working on Sip relocation.

Re: Calls are not working on Sip relocation.