Hi Steven, Thanks for your support man..Input gain 0 worked.. thanks again. regards, ... View more

hi, I see as command accepted its trying to boot new ios after i send reload but i think failed to start with new ios. pls read the error...... Ruoter(config)#boot system flash:c2801-advipservicesk9-mz.124-15.XZ2.bin Ruoter# Ruoter#wr Building configuration... *Sep 29 09:21:06.815: %SYS-5-CONFIG_I: Configured from console by console[OK] Ruoter# Ruoter#dir Directory of flash:/     1  -rw-    37171980  May 21 2010 22:59:04 +00:00  c2801-spservicesk9-mz.124- 15.T13.bin     2  -rw-        2898  May 21 2010 23:00:12 +00:00  cpconfig-2801.cfg     3  -rw-     2938880  May 21 2010 23:00:36 +00:00  cpexpress.tar     4  -rw-        1038  May 21 2010 23:00:48 +00:00  home.shtml     5  -rw-      122880  May 21 2010 23:01:00 +00:00  home.tar     6  -rw-      527849  May 21 2010 23:01:16 +00:00  128MB.sdf     7  -rw-     1697952  May 21 2010 23:01:42 +00:00  securedesktop-ios-3.1.1.45 -k9.pkg     8  -rw-      415956  May 21 2010 23:02:00 +00:00  sslclient-win-1.1.4.176.pk g     9  -rw-    46545492  Sep 29 2010 08:29:44 +00:00 c2801-advipservicesk9-mz.1 24-15.XZ2.bin 129720320 bytes total (40280064 bytes free) Ruoter#reload Proceed with reload? [confirm]^[ *Sep 29 09:21:53.975: %SYS-5-RELOAD: Reload requested  by console. Reload Reason : Reload Command. System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc. PLD version 0x10 GIO ASIC version 0x127 c2801 platform with 393216 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled Readonly ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb80 open(): Open Error = -13 loadprog: error - on file open boot: cannot load "flash:c2801-advipservicesk9-mz.1"       I think here its trying boot but failed???? System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc. PLD version 0x10 GIO ASIC version 0x127 c2801 platform with 393216 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled Readonly ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0x237316c Self decompressing the image : ################################################# ################################################################################ ################################################################## [OK] Smart Init is enabled smart init is sizing iomem   ID            MEMORY_REQ         TYPE                 0X003AA110 public buffer pools                 0X00211000 public particle pools                 0X00020000 Crypto module pools                 0X00120000 VPM buffer pools 0X0621          0X00000000 UNKNOWN Card in slot 0                 0X000021B8 Onboard USB If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Allocating additional 29569078 bytes to IO Memory. PMem allocated: 362807296 bytes; IOMem allocated: 39845888 bytes               Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.            cisco Systems, Inc.            170 West Tasman Drive            San Jose, California 95134-1706 Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(15)T13, R ELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc. Compiled Wed 07-Apr-10 12:07 by prod_rel_team Image text-base: 0x60086E28, data-base: 0x62C02AE0 Cisco 2801 (revision 7.0) with 354304K/38912K bytes of memory. Processor board ID FCZ1421C5UE 2 FastEthernet interfaces 1 DSP, 8 Voice resources DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 126976K bytes of ATA CompactFlash (Read/Write) Press RETURN to get started! ... View more

hi Ash, at configuration level the command is boot system flash Router(Config)#boot system flash c2801-advipservicesk9-mz.124-15.XZ2.bin Router(Config)# Router(Config)#wr mem Router(Config)# all commands accepted so i reload the router but again the old IOS boots. pls advise. ... View more

hi, Ash. I tried tftp32 suggested by you and it worked smootly. the bin file is transfted successfully now. now i can see 2 ios: the old is still exist, then should i delete the old ios so the new will automaticlly boots? pls see attached and guide. Thanks once again. ... View more

hi, kindly see the attached file details ... View more