04-22-2005 08:48 AM
Dear All,
I'm using cisco 7200 as a gateway connected to E1 with PSTN , I upgrade the IOS to 12.3 , but non on my carriers can terinate calls with codec g723 , only g729 is working .
when i send call with G723 codec i get disconnection cause no resources 47
below are output of show version:
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IS-M), Version 12.3(13), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 10-Feb-05 06:58 by ssearch
Image text-base: 0x60008AF4, data-base: 0x61CA2000
ROM: System Bootstrap, Version 12.2(4r)B2, RELEASE SOFTWARE (fc2)
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.1(8a)E, EARLY DEPLOYMENT RELEA
SE SOFTWARE (fc1)
Dolphin uptime is 40 minutes
System returned to ROM by reload at 19:04:49 UTC Fri Apr 22 2005
System restarted at 19:06:35 UTC Fri Apr 22 2005
System image file is "disk0:c7200-is-mz.123-13.bin"
Last reload reason: Reload command
cisco 7206VXR (NPE400) processor (revision A) with 114688K/16384K bytes of memory
.
Processor board ID 29354828
R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2 Cache
6 slot VXR midplane, Version 2.7
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 400 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO <www.cisco.com>,
for c7200 bandwidth points oversubscription/usage guidelines.
2 FastEthernet/IEEE 802.3 interface(s)
7 Serial network interface(s)
4 Channelized E1/PRI port(s)
1 Voice resource(s)
125K bytes of non-volatile configuration memory.
47040K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
04-23-2005 07:55 AM
Hi,
Are you using a voice class codec to negotiate the codec other than the G.729?
Regards
Darren
04-23-2005 11:18 AM
hi,
Yes i configure voice class to support mutiple codecs :
voice class codec 1
codec preference 1 g729r8
codec preference 2 g729br8
codec preference 3 g723r63
codec preference 4 g723r53
thanks
Alaa
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide