Hello, I want to forward calls received from PSTN (condo buzzer system) to SIP. I used to own an older Linksys SPA adapter which has recently died and I can no longer access its settings, nor find the link to the page I used to set things up. Can som...
Hello,I registered a SPA122 on a SV8100 NEC pbx; the device is correctly registered and can make outgoing calls but it can't receive any calls...The caller receives the busy tone when calls SPA phone number.If I register a CISCO IP...
Hi can someone help me configure my SPA112 so that the caller's light is displayed on my phone. I have alerady updated my firmware thanks for the answers
I have several SPA112 units which I have reset and have attempted of access for configuration with no response from the units. The units are receiving a DHCP address as confirm by the router as well as the keypad access which tells the IP address re...
Ola, estou com 2 pap2 bp bloqueados por não saber a senha do administrador, não consigo configurar na minha 3cx.Alguma forma de ajuda? Hello, I have 2 pap2 bp blocked for not knowing the administrator password, I can not configure it in my 3cx.Some h...
Brand new device (purchased from Amazon)Firmware upgraded to 1.4.1SR1(002)Factory resetProfile_Rule set using /admin/resync?http://server/init.cfgSome parameters are set including Profile_Rule_B, Profile_Rule_C, etc (all configs pasted below)Device s...
I have an SPA 112. I have two Sip coming and 1 DID. Both ports are active and registering however the calls that come in through Voice Port No. 1 when its busy Voice Port No2. doesn't ring? I am not sure how to fix this issues? All I need is that whe...
The SPA100 Provisioning Guide contains a chart of valid Time_Zone values for some timezones (https://supportforums.cisco.com/docs/DOC-26259), but there is no specification of what the values mean. The default value is "-08 1 1". The first number is...
Is this possible if so how?
I purchased a SPA 303 IP Phone and have Google Fiber internet. When I hook up my phone to my Fiber box, the phone screen reads "Initializing" but then nothing happens. There's no dial tone. 1. Is the SPA 303 IP Phone compatible with Google Fiber? I a...
I have a Cisco CP-8861-3PCCSoftware version sip88xx.11-0-0MPP-7.loads When I put the handset on hook, it keeps going "off-hook" and then back "on-hook" as if I had picked up the handset, or it was not properly put on the cradle. It is as if the hand...
Hello! I have the following dial plan in a Cisco ATA with Router SPA122: (99999 | *xx*xxxxxxxxx.# | *xx*xxxxxxxxx.*xx# | *xx*xx# | #xx# | <:0224>[2-9]xxxx. | <:0224>1[02-9]xxx. | xxxxxxxxxx.) Is there a way to modify it to avoid the following?:1. Int...
SPA9000 ver 6.1.5 tries to register into ITSP every second when STUN server options are set.Register and inbound calls are sucsesfulSysLog Server shows:<151>[5060]STUN trying 0<151>[5060]STUN trying 1<151>[2]REG: STUN c0a80148->ba5c9a64, 5060->5060<1...
DTMF for in-call applications does not work on my SPA303. The receiving computer cant 'hear' the tones. The online manual says there are two options - In-Band and Out-of-Band (RFC-2833), and goes on to recommend Out of Band. But the config utility ha...
Can Cisco SPA122 box work as SIP gateway?My PBX (SIP Only) cannot understand format what the sip provider specifically requires (P-Asserted-Identity with specific format) but SPA112 can.So what I want is I want to connect my PBX to LAN port of SPA122...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: