09-12-2011 09:22 AM - edited 03-21-2019 04:39 AM
Hi All,
Has anyone gotten FAC to work with the UC560? The box only crashing when the voip is enabled. When i shutdown the voip it makes the calls successfully.
can help is greatly appreciated
here is the configuration
Place the files in flash enter_account.au and enter_pin.au
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authentication login h323 local
aaa authorization exec default local
aaa authorization exec h323 local
aaa authorization network sdm_vpn_group_ml_1 local
aaa authorization network h323 local
application
service clid_authen_collect
param uid-len 3
param pin-len 6
dial-peer voice 50 voip
service clid_authen_collect
destination-pattern 9[2-8]......
session target ipv4:192.168.20.1
incoming called-number 9[2-8]......
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 100 pots
destination-pattern 9[2-8]......
preference 1
port 0/1/0
forward-digits 7
09-13-2011 07:03 AM
Hi Andrian;
Please stay tuned for help. I will ask a colleague to give you a hand on this.
Regards
Alberto
09-13-2011 12:18 PM
Hello Andrian,
There are a few things I noticed, not sure if they are just left out, or not configured.
Your config does not have any usernames/passwords configured, and the dial-peer is pointing to the CME address. Here is the info I found, with the steps to configure FAC.
https://supportforums.cisco.com/docs/DOC-9795/
application
service clid_authen_collect
param uid-len 3
param pin-len 3
aaa new-model
aaa authentication login h323 local
aaa authorization exec h323 local
aaa authorization network h323 local
username 201 password 123
username 201 autocommand exit
username 202 password 321
username 202 autocommand exit
dial-peer voice 5500 voip
description International Calls
service clid_authen_collect
destination-pattern 9011.T
session target ipv4:10.1.1.1
incoming called-number 9011.T
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
Thank you,
Darren
09-13-2011 12:45 PM
Hi
I have the username and password in the configuration and also i've configure 192.168.20.1 as the cme ip address.
05-25-2012 03:10 PM
could you solve it? I have the same problem
Best Regards
05-26-2012 04:55 AM
hello Alan,
got the issue fixed . you need to upgrade the uc560 version to 8.6 .
regards
Chris Henderson
05-27-2012 09:31 PM
Well the most recent is the 8.2
Thanks, let me try
best regards
05-31-2012 08:53 AM
hello Alan ,
following up to see if you got the issue resolved ?
Regards
Chris Henderson
06-03-2012 05:21 PM
hello Chris,
I could resolve it thanks, in my case it was problem with the configuration.
best regards
12-19-2012 11:02 AM
Excuse me, what was your configuration error?
01-09-2013 10:23 AM
Hello Erick,
I do not remember, but works when apply a Factory Reset and reapply the configuration.
Best Regards
01-09-2013 10:33 AM
hahaha i think the last resource always works (reseting the device). I did that on our 3825 and FACs works well.
Regards,
01-14-2013 08:28 AM
nice hear that,
Best Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide