VPN

We have purchased a couple of Cisco 891 routers - both are running IOS 15.0(1) M5 licensed with advanced IP services (default).The literature for these devices on Cisco's website claims they support IPsec stateful failover on advanced IP services.Our...

The Title is probably not very clear.  Here is what I am trying to find out.If I have an ASA that has a Site-to-Site VPN set up on it that has interesting traffic defined as network 10.208.0.0/16 but is also the end point for remote access VPNs where...

A office use Windows Server 2008 R2 (routing and remote access)  for user VPN connection.At other location B office, I want to setup a router (RV120W Wireless-N VPN Firewall) for L2TP VPN connect to A office.B office use ADSL dial connection, and set...

Hello,Does anyone know what is default max-logins for vpn client group on ios 15.1? That should be max number of simultaneous users with the same username. With this command max-logins I can set maximum 10 simultanouos users with same username, is it...

在ASA上建立的REMOTE VPN 连接使用ACS 5.2 作为AAA认证服务器,REMOTE VPN 用户在ACS 中建立,在Internal Identity Stores->user中添加用户,在 System Administration>configuration>Dictionaries>Identity>Internal Users中添加一个IPv4 address属性后,在用户属性中配置固定IP地址.但是EASY VPN 拨号成功后无法获得地址,在ACS 4.2中用户配置固定I...

Hi Experts,I have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.I tried to create a new IPSEC vpn to a gateway loadbalancer.Device is PLANET MH2...

Hi DearsI have a this issue. I think that someone can help me.i configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.xthe project is that:the remote site want the interesting traffic like that:sourc...

I'm having problems getting AnyConnect clients to reach a server (192.168.139.3) on the Inside interface of my ASA 5505.  Ideally, this would be accessible from the DfltAccessPolicy or another dedicated policy, but right now I'm happy with any access...

I have a PIX 515 and am working with a Site-to-Site VPN.  When I do not specify a filter on the Group Policy I can successfully access the remote network and the remote network can access my local network.  However this by itself poses a securty risk...

I have a printer as the sole client on one end of a site-to-site VPN, and the tunnel times out. There is no ability to generate traffic from the printer, so I am looking for anyone that may have a solution to this problem.Printer end - ASA5505Other e...

HiI have a problem with ping in VPN Client,In this senario, the VPN client should be able to ping PC-4 through ASA-1 (Site-A)but it could not.The router is able to ping Z.Z.Z.0/24.The Tunnel and VPN client are working.-------------------------------...

Is anyone running 8.4.2?  If so, have you seen any issues with this version?  I have been testing this code in my lab for the past four weeks and haven't seen any issues that would prevent me from upgrading my production ASA active/standby pair but w...

Hi I was wondering if anybody had any ideas about my remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects o...

I am trying to configure when an employee logs in it scans to verify first that Antivirus is installed in our case Sophos, and that it is running, and has been updated DAT file wise with in the last 10 days, if not go to our server for the update bef...