I configured a ASA Site-to-site VPN, and it passed the packet tracer. I then added Nat on one side for the server on the ASA, and it breaks the tunnel in packet tracer. As you can see in the screencap. I don't understand why it's failing with NAT.
Hello all,I am attempting to set up a site to site vpn between a ASA 5505 and a ISR 871. I used the instructions I found on this website:ASA 55056. crypto isakmp policy 57. authentication pre-share8. encryption aes9. hash sha10. group 211. lifet...
Currently we are allowing remote access vpn users access to the Internet, our setup is as follows:group-policy VPN attributes dns-server value 192.168.100.10 vpn-filter none vpn-tunnel-protocol IPSec split-tunnel-policy tunnelspecified split-tunnel-n...
Hello,On my 2611XM (c2600-advsecurityk9-mz.123-11.T2.bin) with no vpn hardware module, my cpu is very overloaded due to the encrypt proc.I know that the solution is to upgrade this box (or to purchase a vpn module). But I would like to know if there ...
Thanks for reading. I currently have a pair of redundant ASA 5510s (ver 8.2) set up with SSL VPN running ASDM (ver 6.2). With the current setup users are able to access the file server via the remote connection but are not allowed to save the file ...
Hello,I configured my asa 5510 to use AD for vpn user authentication. Although i'm using l2tp ipsec I used following document as a guideline https://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00808c3c45.shtml#prereq. Wh...
Hello,Hope anyone can give me an hint .....My problems is that multi customers, all connected with site-2-site vpn, use the same ip-segments on there lan (ip-overlap) so i needto do vrf-aware IPSEC as a understand it.I have setup an testlab but it do...
Hello,I have used the password recovery procedure on a Cisco 831, with success (password changed), however the ipsec vpn is not working anymore.I have the folloqwing message : %CRYPTO-6-IKMP_MODE_FAILURE: Processing of Informational mode failed with ...
Morning All,I have a VPN with a Cisco ASA 5510 and a Cisco 2600, all has been working fine for ages but this morning I'm recieving the following error on my ASA device.Does anyone know what i need to do to clear this? If it is a common issue that is?...
Hi, I have enabled cache cleaner in SSL VPNs, but the user can avoid installation pressing skip and login without cache cleaner,Is there any way that the user can not prevent the installation?I want to make compulsory the use of cache cleaner to co...
Hi,I have a strange issue concerning the VPN IPSec client.After 19 hours and 14 min (sometime it's around 19hours and 27min), the VPN client is disconnected.It has nothing to do with the station, I've tried it on 4 differents stations / operating sys...
Hi everyone..I'm setting up an IPSec tunnel between your primary site (with checkpoint) and a customer, having an Cisco WRV210.The tunnel is established, and working, since I can ping from our site, to the customer, but the customer LAN can't ping ou...
My situation is a near exact duplicate of the guy on recent post #3107277 except that we want to use an RV042 on our end. Is that possible on an RV042? I got a succesful VPN connection but cannot ping a known host on their end, presumably because t...
when I use the quick vpn client to connect to the RVS4000 at work, it goes through the connection process to the point where it says "verifying network", it then stop and gives a message that the remote gateway is not responding. When I check the VP...
I have 2 5520's. I want to load balance them for AC VPN Sessions. If I cant get this working I'm going to the old standby DNS Round Robin.So I have a cluster IP Address and I've assigned a hostname to that IP.Lets call it: ANYCON.TEST.COM/COS (...
