VPN

Good day,We currently have a Cisco ASA 5510 with version 5.2 of ASDM and version 7.2 of the ASA. It is my understanding that to use the Cisco AnyConnect client we would need version 6.0 of the ASDM and version 8.0 of the ASA. If this just a software...

I would like to terminate two or three tunnels (3DES) on a 7206VXR w/NPE-G2. I expect throughput to peak at 30Mb/s.How much throughput can I squeeze out of a 7206 [before I want to add hardware-assist, e.g. SA-VAM2+]?--skStuart KendrickFHCRC

Hi,Is it posible to configure ( ISR 3845 ) for Site-to-Site VPN with RSA authentication? Without any certification server to issue any certificate. Please share the experience any configuration example on cisco.com is highly appreciable.Thanks in adv...

Our main office (Cisco 5505) is connected by cisco vpn tunnels to 4 other sites.I would know of it's possible to connect to the main office and with this vpn connection reach all other connected sites.Now I must connect to all other sites seperatly i...

I am seeing occational syslogs of these type on a 1711 router running IPSec:%CRYPTO-4-PKT_REPLAY_ERR: decrypt: replay check failed connection id=3, sequence number=0Does this mean that an ESP packet was seen with a sequence number of 0? What ...

I'm running into an issue with a L2L VPN we have between one of our remote sites. At times one of the many networks there will stop passing traffic across the tunnel. Other networks at this location will continue to traverse the tunnel just fine when...

I am having a problem setting up a L2L tunnel with a partner. I am using a ASA 5520 running 8.0.4. Both sides of the tunnel are using the subnet 10.30.x.x/16. The network list on my side of the tunnel will have the nodes 10.0.194.1, 10.0.194.5, 10.0....

I have a 3845 and a 2821 router. I want to configure a router-to-router VPN as a backup to the WAN connect. If the WAN goes down the VPN on the 2821 will kick in and establish a connection to the 3845. I am using EIGRP and BGP on the network. Routin...

hello!i recently configured on a cisco asa 5520 remote access using ipsec.the remote client uses cisco vpn client.the vpn client successfully authenticats and connects to the asa, however i dont have access to the lan. this is the first time that i c...

Hey Pros!We have an ASA here with two ISP links running directly to it. The ASA provides Lan-to-LAN VPN tunnel services between us and our partner company. The partner company has two separate sites, which we will call Site A and Site B. Our ASA's pr...

I have an ASA5520 running 8.0.4. I need to create a tunnel with a vendor using the same internal network as we are. They are unable NAT on their side. I would like both sides to be able to bring up the tunnel. They are using 10.2.x.x/16 as their ...

I'm finding out VPN bandwidth calculator or any formula to calculate bandwidth related to remote VPN. Let's say, 250 simultaneous/concurrent users connection. What is typical average per conn I think? including voice traffic as well? How much BW i ne...

Dear All,I want to ask abut VPN connection.the both side i used ASA 5510 and 5505 and VPN connection. so the branch it can ping to HQ(i mean the VPN connection is ok) but i want the branch they can use internet from HQ.but know the branch cannot use ...

I'm installing some new ASA 5520's which will be used strictly for VPN connections (both lan-to-lan and client connections).I have some questions about the best way to setup redundancy and failover and integrate it into our network. I've attached a d...