VPN

I have users that connect to a ASA5510 using the cisco VPN client version 5. Policy dictates that the users must access the Internet through the corporate firewall when connected via the VPN. I have been unable to get web traffic to work. I can ac...

Hi,i have a pair of VPN connection from PIX515-E, after issuing the command:clear crypto isakmp sanow none of the VPN tunnels come backup again and show isakmp sa - show something like thismbryonic : 0 dst src state ...

Hi all, I have just set up a vpn tunnel from site to site, but it does not allow me to ping through it, the error on the logs is An ICMP session was removed in fast-path when stateful ICMP is enabled using the inspect icmp command. Can anyone help ch...

I recentl switched back at home to just my 1721. Now my ras vpn does not work. When I vpn in from inside(trying to secure my wireless) it connects however all the packets get discarded by the vpn client. The only thing thats different is my intern...

Hi, team!There is a way to configure user-list for syslog on VPN 3000 concentrators. I have to use following format: "Event Class / Event ID, SEV(No)"I know couple of events like this: "AUTH/22,SEV(4)" - that means "IPSec user connected"Where can I f...

Hi, I would like to setup VPN between our HQ and users thru internet. The router in the HQ is 827 4v (12.2(3)). Is it possible to setup a VPN on this router?What should i need the minimum requirement of router specs to achieve the above mentioned goa...

Hello there,i'm new to this forum and starting to complete my CCNA 3! I hope my english isn't too bad ;)I had to do a project for school, so i choosed "VPN", because it interested me very much. i would like to configure two Cisco 2610 Routers (with t...

Hi,I have applied an ACL inbound on the internet interface to secure the router, but some internal networks cannot access the internet. My ACL looks like this.ip access-list extended InternetInremark "Allow inbound Web"permit tcp any eq www host 209....

It is my understanding that in order to restrict vpn connection either site-to-site or client via ports the "sysopt connection permit ipsec" command needs to be disabled and the control then comes from the access-list that is inbound on the outside i...

I?m getting ready to shutdown and MPLS circuit and cut over to a site to site VPN. The tunnel will be between two PIX?s running 6.3.x. Once I disable sysopt connection permit-ipsec on both firewalls and modify the incoming access-list, users from...

If an IPSEC tunnel enters MM_NO_STATE on a PIX Firewall while live and no parameters have been changed and all Phase 1 parameters are correct, what can be done to reset the connection without restarting the device?

Hi,Have a 3 site PIX VPN running just fine. We also have PPTP incoming to the head ofice just fine. However, the PPTP users cannot access the remote sites when they are connected to the head office PIX. The remote users have the "use default gateway"...

Currently I have a small inquiry about a PIX506E, this device is configured and working fine, VPN is also configured on it to allow LAN-to-LAN connection using crypotomap and user authentication access PPTP with MSCHAP.Problem Description- I connect ...

Hi!Im new to ACL's. This is my question. Is ACL will take effect in an interface in a pix even if this ACL is not used in a access group command?example:access-list inside_access_in permit ip any host CFS016Just like that. Co'z i can't find any acces...

Good Morning NetPro Community,I'm new to configuring the 5510/5505 for VPN. I have the VPN nailed up between the 5505 and 5510, but I can't get the 5510 to hand out IP's to the 5505. Any ideas what I'm missing? My config for the 5505 is below. I ...