VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

I have a user that has a home network and uses a domain there. She can get to the VPN at the office, but when she connects, she can no longer access shares or printers on her home network. Can this be done? We are using a PIX 515, a RADIUS server,and...

jimburris by Level 1
  • 541 Views
  • 3 replies
  • 0 Helpful votes

Hello,I am trying to setup a vpn between two 827's on an adsl line (3 later), I havedone vpn's on Netscreen's, but I am a bit lost with the Cisco(I know basic cisco stuffshow run / Conf t /Interfaces config)Could somebody point me too some good doc?W...

sre by Level 1
  • 420 Views
  • 2 replies
  • 0 Helpful votes

Hi all,A general question.How do I find out if an ISP lets me pass VPN traffic in thair network? I hear most Cable \ DSL providers block Ipsec traffic. Is thare a way of finding out. I have a PIX 520 that I want to be reached by an CPN client. It wor...

Hello,This maybe a question to help all PIX VPN guys.Is there a standered order of entering the PIX commands for PIX-PIX VPN commands. I've experienced some PIX firewall hangs when you type in some commands.THNX

Hi, I have Cisco 515. I need to configure VPN with our clients and customers. By default my Pix is VPN Disabled. I got the new authentication key from Cisco for DES. Now to make it enable i and given the new authentication key i need to boot in rom...

I have a Cisco 1751 Router. I would like to have employees be able to access our network from their homes through a VPN tunnel. Can anybody tell me which ISO version I need to apply so that this would be possible? Thank you in advance.

djamison by Level 1
  • 582 Views
  • 3 replies
  • 0 Helpful votes

We are currently planning to implement a remote access VPN solution for our telecommuters and mobile users. The VPN tunnel will be terminated on our existing PIX firewall 520 with OS version 6.1. Could someone please recommend the best VPN client to ...

shabika by Level 1
  • 417 Views
  • 2 replies
  • 0 Helpful votes

Hi, We currently have remote access vpn in place and working fine. What I now what to do is to restrict access for a particular external client to a single host within our network, while still allowing full access to everyone else. Is this achieveabl...

saluko by Level 1
  • 573 Views
  • 6 replies
  • 0 Helpful votes

Is it possible to limit the number of vpn client users?I am using a PIX 515 configured to authenticate users against the RADIUS server that comes with Windows 2000. I'd like to limit concurrent users, if at all possible.TIA-Matt

mgeneral by Level 1
  • 356 Views
  • 1 replies
  • 0 Helpful votes

Is it possible to extend ones network through an IPSec tunnel? In other words - can the IP addresses of hosts on both ends of the IPSec tunnel be on the same IP network? Scenario: We have a wireless LAN setup and want to put PIX 501's on either en...

1dkelly by Level 1
  • 726 Views
  • 3 replies
  • 0 Helpful votes

I have a 2620 with a 16 port async modeult for RAS dialin. I also have two T1 WIC's that I use to connect to a remote site (ppp multilinked). Can I setup the router to provide authentication for the PPP dialup users but not on the two T1's? I can't f...

cclark by Level 1
  • 405 Views
  • 1 replies
  • 0 Helpful votes

Hi.Has anyone found a smart way to handle large number of SA's and peers on a PIX VPN installation?Example: To check if a SA has been created you have to issue a "show crypto ipsec sa". This will list all SA's on all peers, in my case about 250 SA's ...

kva by Level 1
  • 417 Views
  • 2 replies
  • 0 Helpful votes